Devanco Canada - Get The Right Garage Door Opener‎ and Parts

65-92131

LiftMaster Dual Aux Trolley Mod. M15 #41 Chain for 12ft High Door

Provides drawbar-type operation on very wide (over 22 ft) standard lift sectional doors where a side-mount op. is preferred over a drawbar op.
Includes up to 12ft of tracks
For H/J/GH

26CW945255

Truck Door Intermediate Panel (15.5" x 98") Painted White for Whiting Dryfreight

These panels are 15.50" height x 98" width.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white

8030279

Marantec Replacement Belt with Tab for 8ft Door

Overall Belt Length = 250"
Travel limit tab attached to belt
For Marantec opener models: M4500 M4700 Q7500 Q7700 Q7900 M4500e M4700e M4900e Synergy 260 Synergy 270 Synergy 280 Synergy 360 Synergy 370 Synergy 380 Synergy Solo
Check the Belt Connector while you are replacing the belt. If it's worn or cracked it should also be replaced

TTC-MODULE

Timer to Close Plug & Play Module

Adjust door closing times from 1 second to 5 minutes
Adjust pre-closing warning times from 2 to 5 seconds
Easy-to use "Plug and Play" connector
Make adjustments using the module's LCD display
Requires installation of monitored entrapment device
111114.500307

.......more details

106-0005

Rodent Block Pull Chain Seal 2"

Often overlooked and left unprotected the opening for the pull chain on dock levelers is an ideal entry point for mice and rats.
The chain provides a built-in ladder for pests and the chain opening is more than big enough for rats or mice to squeeze through.
Features solid cast aluminum construction easy to install and completely cover the chain opening.
The seals are designed to sit completely below the surface of the dock plate and will not interfere with material handling equipment.

OSH-6812-ECB-LH

Manaras Opera-SH 1/2 HP 208V 1Ph with Electronic Circuit Board Left hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

106-0006

Rodent Block Pull Chain Seal 2.5"

Often overlooked and left unprotected the opening for the pull chain on dock levelers is an ideal entry point for mice and rats.
The chain provides a built-in ladder for pests and the chain opening is more than big enough for rats or mice to squeeze through.
Features solid cast aluminum construction easy to install and completely cover the chain opening.
The seals are designed to sit completely below the surface of the dock plate and will not interfere with material handling equipment.

0220-1K-390

Heddolf 1-btn Overhead Compatible Remote 9 Dip Switch 390 MHz

Overhead compatible full-size transmitter

CP-SH-58-1038-LS

Lynx Limit Shaft Only

5/8" x 10-3/8"
Used on most of Lynx operators

2528.087

Whiting Dual-Spring Shaft 87" for Whiting Roll-Up Doors

Constructed of 1" outside diameter heavy-duty steel tubing
Holes pre-drilled
Cross Reference: For Whiting # 2376 balancer

14-1002

PVC Roll 8" x .120" Standard Smooth 200' for Replacement Strip Curtain

Suitable for most average applications.
Temperature Range: -20°F to 150°F (-28° C to 66° C).
Formulated with ingredients that meet USDA requirements for incidental food contact.

LA400-JB40

LiftMaster Junction Box w/Cable 40'

IRB-325-HD

EMX Industries Steel Protective Hoods Only Grey Powder Coat Set of 2

Protective Hoods for the Thru-Beam Photo Eye System (Item #IRB-325) by EMX
Easily installed using the existing mounting holes of the Photo Eye
Constructed of zinc plated steel
Grey powder-coated finish
9" x 3"

510.4228.07

Whiting Double End Hinges DF SS/Nylon - 7 Panel Door Add-On Option

Add-on option when ordering door.

74183

Marantec External Gate Receiver 315 MHz

Upgrade your existing gate operator to be compatible with Marantec controls such as transmitters and keyless entry systems.
315 MHz operating frequency
HomeLink compatible
Very easy installation (follow wiring diagram of gate operator)
Compatible with other operator brands

BRAKEPART020

Manaras Brake Shoe Assembly Kit (SHOE021/022)

510.2543.00

Whiting Narrow Mounting Angle for Posts Under 2-1/2" IN

This is an upcharge when ordering certain doors

CP-PW-NM-34

Lynx Pocket Wheel for HDC

15-10885

LiftMaster Dual Sprocket 48B10/41A24

Also known as: G1510855 156016 G156016 15-10885 15-6016 71156016

SL585501UL

LiftMaster Industrial Slide Gate Op. 1/2 HP 115/230/208 Volt 1 Ph Heater NOT Incl.

Features a heavy- duty industrial lockable metal cover
MyQ® Technology enables you to securely control and monitor your gate operator from anywhere
Homelink® Compatible (version 4.0 and higher)
Security+ 2.0® safeguards access with an encrypted tri-band signal to virtually eliminate interference and offer extended range.
Manual Disconnect when unlocked allows gate to be operated manually.
Quick Close and Anti-tailgate quickly secure property preventing unauthorized access

.......more details

LOTBINIERE-R16

Garex Ready to Install Door Special Order

R16 Insulation - Overlay moldings positioned to create the Lotbiniere design - Moldings are factory white or can be factory painted to match door colour - Optional decorative hardware is available - Available in steel (std colours) or aluminum (white and grey) - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements - Composite end blocks eliminates corrosion and wood deterioration

URBAN-MR-R16

Garex Ready to Install Door Special Order

R16 Insulation - Narrow multi rib pattern - Available in steel (std colours) or aluminum (white and grey) - A variety of decorative windows can be added - Custom colours can be factory painted - Multiple hardware configurations are available to accomodate site requirements - Composite end blocks eliminates corrosion and wood deterioration

2806.187*300

Whiting .187 x 2-3/16 x 30" Roadside with Cones

D800-120-125

Cable Drum High Lift 800-120 1-1/4" HL Pair

Adjustable cable attachment with screw
Made of aluminum
High Lift capacity: 120" max
Flat capacity: 266" max
Rating: 2200 lb per door max
Keyway: 1 KW of 1/4" width

.......more details

2807.177.230

Whiting Spring Assby .177 x 2-3/16 x 23" Curbside

Replacement torsion spring with cones
Specs: .177 x 2-3/16" x 23" Long
For Roadside order part # 2806.177.230

26-40019

Truck Door Bottom L-Retainer 90" Long for Todco Roll-Up Doors

Galvanized steel construction for extra strength and corrosion resistance.
Fits both standard and heavy-duty bottom seals.
Pre-punched holes for added convenience
Cross Reference: T #61191 W #4034 260000

IRB-SH-SET

EMX Industries Steel Protective Hoods Only Grey Powder Coat Pair

Includes 2 hoods
Powder-coated steel construction
Compatible with EMX IRB-MON EMX IRB-4X safety photo beam sensors
Each hood fits easily over gate/garage door opener sensor

PUSH148

Manaras Contact Block NO

Same as ZEN-L 1111

MX00218

Micanan Clutch Shaft Assembly for PRO-LH

1013-1-1/4-18'

Rigid Vinyl Bottom Retainer L-Shaped 18' Long

For door thickness: 1-1/4"

12-3000

Flanged Bearing 1-1/4" x 1/8" **to extent of inventory

Fits SW470 gate operator

LA500SLRHARN

LiftMaster Solar Harness Kit LA500

.289_3-3/4"-RH

Torsion Spring .289 x 3-3/4" x 12ft RH

Wire size: .289
Inside diameter: 3-3/4"
Length: 12 ft

ERN

Erone 4-Channel Transmitter 433MHz

Innovantive and extreme crashworthiness
Casing: aluminum and black polycarbonate
Range (line of sight): up to 250 m (820 ft).
Dimensions: 70 mm x 40 mm x 10 mm (2.75 in. x 1.57 in. x 0.4 in.)
Comes with: One lithium battery (2032)
Optional 26-bit Wiegand proximity tag built-in: ERN (old #S7TR2641E4T (HID) old # S7TR2641E4M (Mifare)

.......more details

.192_2-3/16_60R

Spring Wire .192 x 2.188 x 60" CTD RAW RH

.192 x 2-3/16" x 12'

.25W8.2

Resistor 1/4 W 8.2K OHM

Dimensions (W X H X L) 6 X 15 X 3 CM

02-406-2

LiftMaster Key Set Qty 2

Replacement Key ONLY for 02-406 2006-2015 #1 or #1502M

422LMC

LiftMaster 2-Channel Co-Axial Receiver 390 MHz ***DISCONTINUED

Smart Garage Door Opener® electronics on each channel for fast programming
Bell wire attached for easy second channel hook-up
18 - 35VAC/DC
FCC certified 390MHz

26117

Doorlec Limit Cam Retainer Plate

Fits Most Doorlec Commercial operators except Explosion-Proof Operators
Will not fit on waterproof operators with small electrical enclosure built before 1999

27-83190

Truck Door W-Style Track and Operator 90 x 90 Door

Includes: 1 dual spring operator 2 horizontal tracks 2 vertical tracks

LM56A

LiftMaster Magnetic Proximity Reed Switch

Normally Open magnetic sealed reed switch; proximity switch
Used for overhead door contacts.

41D4509

LiftMaster Motor Kit ATS211

Also known as: K75-16424 41D4509 123D0155 123D155

K180A0357

LiftMaster Reset Switch

Compatible with LiftMaster RSW12UL CSW24V swing gate operators
Switch to Reset/Disconnect position to disconnect the operator for manual operation
Switch to Normal Operation position to return to automatic gate operator functions
Dimensions: 3/4" L x 3/8" W x 2" H

TRANSF005

Manaras Transformer 120V-24V 40VA

Transformer 120V Primary 24V Secondary 40VA

K23-34815-1

LiftMaster Stop / Reset Switch

For use with SL595UL Series heavy-duty industrial slide gate ops

60-6560-A-YELLOW

Speed Bump Yellow 36" Econo Light Weight for Asphalt

A standard speed bump system section includes (2) main pieces (2) endcaps x 5” long and (1) connector clip.
Main pieces may be added and connected to form larger units.
36” long x 10.5” wide x 2” high (main piece)
EndCap: 5” Safety Snap On End Cap - sloped modular profile prevents tripping by pedestrians.
Yellow Plates: Each speed bump section is embedded with (6) yellow safety plates of weather resistant composite material for protection from salt freeze and thaw.
Can be used as a cable cover - bottom sides include 1” x 1½” channels for protecting temporary or permanent cables or hoses.

.......more details

60-6550-C-BLK

Speed Bump Black 36" Econo Light Weight for Concrete

A standard speed bump system section includes (2) main pieces (2) endcaps x 5” long and (1) connector clip.
Main pieces may be added and connected to form larger units.
36” long x 10.5” wide x 2” high (main piece)
EndCap: 5” Safety Snap On End Cap - sloped modular profile prevents tripping by pedestrians.
Yellow Plates: Each speed bump section is embedded with (6) yellow safety plates of weather resistant composite material for protection from salt freeze and thaw.
Can be used as a cable cover - bottom sides include 1” x 1½” channels for protecting temporary or permanent cables or hoses.

.......more details

620-101293

Linear Apex II Module

Newer model from Jan 2016
The APEX II is backwards compatible but you will need to add monitored external entrapment devices.

29138

Doorlec Transformer 208V pr 120V sec 50VA

208V prImary 120V secondary 50VA

K21-38158

LiftMaster Current Sense Harness Kit 3PH L5

This is a Current Sense Harness (230/460/575V) Replacement Kit.
Compatible with various LiftMaster® 3 Phase Logic 5.0 Commercial Door Operators; manufactured after February 2016.
Complete replacement kit includes: (2) current sense harnesses of different lengths to accommodate all models.
Models manufactured before February 2016 DO NOT feature current sense technology.
We highly recommend replacing the existing boards with an updated Logic 5.0 system that utilizes current sense technology
Refer to the following replacement boards for compatible upgrades: K001D8395 1PH/3PH Logic Board for all L5 models K001D8397 3PH/L5 Power Board 230/460V

.......more details

RELAY008

Manaras Relay AB 700-HA33A24 11 Pin TP

Allen Bradley

10.1003.150

Whiting Step Bolt Stainless Steel 1-3/8"

M-0319

Autogate Groschopp Inline Motor 24V

050DCDDOWF

LiftMaster Receiver Logic Board WiFi Dock Door Jackshaft

050DCDDOWF is a Receiver Logic Board Replacement Kit.
Compatible with LiftMaster® Model DDO8900W DC Light-Duty Commercial Jackshaft Operators; featuring WiFi®

CBC532-SS

Thimble 5/32" Stainless Steel Sold Individually

7001-12-ANODIZED

Commercial Side & Top Weather-Strip 12' Long - Anodized 7001-AB

Anodized galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

7001-7-ANODIZED

Commercial Side & Top Weather-Strip 7' Long - Anodized 7001-AB

Anodized galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Also known as Taupe
Full case quantity only (20)

CGH151L5-RH

LiftMaster Gearhead w/ Brake & Carwash Mod. 1-1/2 HP 115/230V 1P L5 - Right Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting except if a Mod is added
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

41A5635A

LiftMaster Receiver Logic Board 390 MHz ** To extent of inventory

Compatible with a number of dual capacitor chain drive models including 2575 2585 2595 PD752 and PD758S manufactured between 2001 and 2005
Also known as: 41A5483-15 41A5635 01A5635A

CP100C

Coupler Specialty Coated 1" Bore

Coated with 1000 plus hr salt spray rated finish
1" Bore with 1/4" keyway
Malleable iron for high strength and resistance to shock loading
Coupler halves separates and is adjustable
4-(3/8"-16 x 1" square head set screws installed
Rust inhibitor coating

.......more details

0/7140/499

Automatic Systems Frequency Drive ATV 12 0.37KW 120V

Frequency drive for AS1620
Only available for G2

7205

Whiting Balancer Bracket End - Roadside for Whiting Roll-Up Doors for #7176 Balancer

Steel construction
Plain finish
Whiting original

7206

Whiting Balancer Bracket End - Curbside for Whiting Roll-Up Doors for #7176 Balancer

Steel construction
Plain finish
Whiting original

BPPB17512

Devanco Bottom PVC Moulding White for 1 3/4" Door U shaped 144"(12')

BPPB17524

Garex Bottom PVC Moulding White for 1 3/4" Door U shaped 289"(24')

ERM40600H00

NICE Era MH Tubular Motor 40Nm 14rpm 120/60 12'

There must be at least 0.4 m between the driven parts and any xed elements
If the cable is damaged the appliance must be scrapped. The power cable cannot be replaced

H7NA12

Richards-Wilcox Hinge 7NA x 12 Gauge Roller Bracket

Galvanized 12 gauge hinge

ME120-BLK-2WIRE-L

Miller Edge Black 2-Wire NM Left Hand Outlet Sold per Foot

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

7-2239

Richards-Wilcox 3" - 7/16" Short Shaft Roller Super 3

Original Richards-Wilcox part
Roller diameter is 3" good for a 3-1/4" track

K20-1150C-2P

LiftMaster Electric Motor 1-1/2 HP 115/230V 1Ph TEFC

Replacement electric motor for SL595-15021 and SL595-15011 models

0/7530/249

Automatic Systems 5/8 Left Hand Rod End with Zerk

Used on the BL229 gate op.

TRACK-SET-2STD-14

2" Tracks Set 14'-0" Torsion 1-3/4" Door Clips for Wood Frame 12" Radius *** By quote only

TRACK-SET-2STD-12

2" Tracks Set 12'-0" Torsion 1-3/4" Door Clips for Wood Frame 12" Radius *** By quote only

MD00019

Micanan Sprocket 50B40 X 1" 1/4" KW 2SS 5/16

CGH101L5-LH

LiftMaster Gearhead w/ Brake & Carwash Mod. 1 HP 115/230V 1P L5 - Left Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting except when a MOD is added
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

MTR1

Linear 1-Channel Visor Transmitter 318MHz

Activates one MegaCode receiver
Test/operate LED
Visor mounting clip supplied
Visor clip mounts vertical or horizontal
Power: One 2032 battery
Codes: 1000000+ (MegaCode format)

.......more details

Programming instructions Instructions de programmation

4JW-LEFT

Rolling Steel 3" Curved Cast Windlock 273002 LH

Windlocks are especially used on rolling steel doors and shutters to prevent "blow-ins" from severe storms or winds.
A wind lock is a small metal device that is attached to each slat.
Its primary function is to reduce the amount of friction that occurs between the actual door & the guiding panel.
When the wind is strong the roller door may be dislodged bent or misaligned from the guide.
With a windlock your door can operate efficiently despite wind load or pressure.
Windlocks are easy to add on to any existing rolling steel or shutter door

.......more details

60-7531

Fasteners Wedge Anchor 3/4" x 5-1/2" 4/Bag

Secure anchoring into concrete brick or block
Ideal for mounting dock bumpers
4 per bag

STATION082

Manaras Push Button Control Station 2-Button Nema 4/12

2-button 2 N/O contact
Plastic

BRX10

GDI Brake Kit Brake Kit with Pull-rods; Axial

HD3120-BLACK

Commercial 3" Inside Slide Lock Black Powder Coated

Track use: 2" or 3"
Throw: 2.62"
Slide bar: 0.138"
Individually wrapped

19-48055MB

LiftMaster Limit Chain Assembly #48 x 55

Fits the SL575 & SL585GL gate operators
Same as K19-48055MB

MD00077

Roller Chain #40 Sold by the Foot

E/BLOP/005

Automatic Systems Standard Tip Support Option

12501

Doorlec Clutch Plate Aluminum 4" dia x 1" bore

Works with models EHJ and ETBH

HAE00012

Linear Motor Cover LDO50

Replacement motor cover only

OSH-6813-ECB

Manaras Opera-SH 3/4 HP 208V 1Ph with Electronic Circuit Board

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

112561

Allstar MVP-RE 24V 8 Wire Receiver 288 MHz *** NLA

Three channels – three relay outputs
8-wire operator connection
Wire whip antenna with “F” connector
Compatible with Allstar Classic Allister and Pulsar dipswitch transmitters and MVP quik-code transmitters
Power: 24 VAC/VDC
Codes: 19683

.......more details

MOD130

Manaras Cogged V-Belt Upgrade

The standard v-belt is replaced by a cogged v-belt for added durability
Applies to: OSH OTH OTH-A.00 OTBH OTBH-A.00
This is available only as an upgrade with the purchase of a commercial op.

GAL.262-258-144L

delete

G-21X13-134-BLK

Thermal Window Clear 21" x 13" for 1-3/4" Garaga Door Black

For 1-3/4" thick door

RBH505L5-RH

LiftMaster 1/2 HP 575 VAC 3 PH Commercial Hoist Operator Logic 5 Right Hand

H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
With the addition of the 828LM MyQ technology enables the user to monitor and control their operator and light with their smartphone tablet or computer.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.
Security+ 2.0™ safeguards your facility – with every click a new code is sent to the commercial door operator so the door opens only for you.

.......more details