Devanco Canada - Get The Right Garage Door Opener‎ and Parts

DR

Linear 1-Ch DR3A Delta3 Receiver 310 MHz

310 MHz frequency 8 dip switches for coding 256 possible codes
24V AC/DC input power 3 terminal connection
Activates one device
Dimensions: 5.5" W x 4" H x 1.25" D
Same as: DNR00001

Installation Manual

NMTK

Linear MegaCode Wireless Keypad 318 MHz Grey

Wall-mountable backlit NMTK is a wireless MegaCode keypad
Requires: 3 AAA batteries for power
It can activate multiple MegaCode Receivers including Linear GDO’s and APeX equipped Gate Operators
User-selectable 1 to 6 Digit/Letter PINs
Programming is easy via the keypad; MegaCode receiver auto-learns PIN
Blue backlit keys for easy viewing

.......more details

Installation Guide (EN/FR)

MTS3

Linear Megacode 3-Ch Visor Transmitter 318MHz (DNT00093)

Operates up to 3 garage doors
Easy to add/remove programming
LED light confirms battery power
Requires one (1) CR2032 coin-cell battery (battery included)
Includes Visor Clip
Ergonomically designed

.......more details

Programming instructions Instructions de programmation

HAE00001

Linear Wall Station

Wired wall station with light and lock features.
For LSO LDO LCO

HAE00040

Linear Control Logic/Receiver Board

Replaces HAE00039
Control board for LSO LDO LCO models

DT

Linear 1-btn Delta3 Transmitter 310 MHz (DNT00002A)

Activates one Delta-3 receiver
Test/operate LED
Visor mounting clip supplied
Power: 9-volt battery
Codes: 256 (set by 8 dip switches)
RF frequency: 310 MHz

.......more details

Programming Instructions

217436

Linear Drive Sprocket - Chain (HCT)

DT4A

Linear 4-btn Delta3 Transmitter 310 MHz (DNT00027B)

Activates one four-channel receiver (DR4) two 2-channel receivers (DR2) or four single-channel receivers (DR DRQP or DRM).
Can also be used as remote UP DOWN STOP control for commercial operators with DR-4 receiver.
8-dip switch 64 selectable codes
Same as: DNT00027B or DT4A
310 MHz frequency

Programming Instructions

7FT-BELT-LDO

Linear 7ft Belt Drive Rail for LD050/LS050/LDCO (HBT7C)

7ft belt-drive T-rail for LDO33 LDO50 LSO50 LCO75 & LDCO800 door operators
Fully-assembled & pre-tensioned
Compatible with Model CHCR-7/8 carriage house I-rail conversion kit

309013

Linear 1-Channel Multi-Code Receiver 310 MHz

Three tabs for universal mounting
One N/O relay
Compatible with 310 MHz Stanley and Multi-Code transmitters only.
Operates on 24 VAC power
One channel
Codes: 1024 (set by dip switches)

.......more details

Programming Instructions

EXA-1000

Linear Omni-Directional Remote Antenna (AAE00198)

The EXA-1000 is a 1/2 wave center fed vertical antenna composed of three parts: an Antenna assembly with an F connector attachment; a Base Plate assembly with radial mounting provisions; and a five-foot 75-ohm coaxial cable.
The cable connects to the antenna base on one end and the receivers F connector on the other.
If the antenna must be mounted further than five feet from the receiver an extension cable of up to a maximum of 25 feet may be used instead of the five foot cable supplied.
Because of the cable resistance the performance of the EXA-1000 may be degraded by using longer than a 25 foot cable
Compatible with all Linear receivers with Type F antenna connector
Receives signals in 288 to 320 MHz range

.......more details

Installation manual

MDR/U

Linear 1-Channel MegaCode Universal Plug-In Receiver 318 MHz

Makes any garage door operator compatible with MegaCode transmitters
Simple plug-in design
Easy to install - one connection using two-conductor wire
Memory: storage for up to 10 MegaCode transmitters
Normally open contact activates for 0.5 seconds
Power: 110 VAC +/- 10% 60 Hz

.......more details

MGT

Linear MegaCode Gate Safety Edge Transmitter 318 MHz (DNT00068)

The MGT is the industry’s only fully supervised gate safety edge transmitter.
It automatically sends an hourly status report to the access controller indicating battery condition and if the transmitter is operational.
Should the edge sensor be disconnected shorted or tampered with the MGT will report a trouble condition.
Features Include:
Signals access controller for stop or reverse when safety edge activates
No cables or coiled wires

.......more details

Programming Instructions

HAE00087

Linear Safety Beam Sender & Receiver with Wire

Set includes: Sender and Receiver photocells wire and connectors
Safety beams will work with all Linear operators that currently have safety beams installed.
Replaced HAE00002

MTS1

Linear 1-btn MegaCode Transmitter 318 MHz (DNT00091)

Activates one 318 MHz MegaCode receiver
Test/operate LED
Visor mounting clip supplied
Two CR2032 batteries included
Codes: 1000000+ (MegaCode format)
Dimensions: 3" W x 1.875" H x .625" D

.......more details

Programming instructions Instructions de programmation

F310

Linear GTO Digital Keypad (Wired or Wireless)

As a wired keypad it can operate garage door openers and gate openers that require 24 volts or less and accept normally open contacts.
As a wireless keypad it can be used with any gate or garage door opener that receives a 318 MHz RF signal.
The keypad must be used in conjunction with the GTO garage door receiver kit (part # RB709) on any other garage door.
You may program up to 25 different personal entry codes allowing you to give different entry codes to different users
After entering a valid code pressing any key while the gate is opening will stop the gate; pressing any key while the gate is stopped and the gate will reverse direction.
The keypad will not affect the auto-close setting of your gate opener system.

.......more details