Devanco Canada - Get The Right Garage Door Opener‎ and Parts

41A7920-2

LiftMaster Hardware Kit

MIRM-T2-50

Miller Edge Patriot 2 Photo Eye Monitored 50ft Non-Contact ** Discontinued

Attaches directly to a Sectional door.
The photo eyes travel below the door during the closing cycle.
Unlike traditional static mount photo eyes; Patriot travels with the door sensing obstructions prior to contact.
The Patriot2 non-contact system consists of thru beam photo optics.
Emitting and receiving eyes mount into a rigid steel spring loaded retracting housing.
The housings attach to the bottom section of the door and extend below the leading edge of the door providing an invisible infrared light beam of protection.
If the beam is blocked the control unit signals the door operator to stop and/or reverse.
It is also available in fail safe wiring configuration (MIRF-T2).
Kit includes: Sender Receiver Telescopic Leg Kit 15 Feet Coil Cord and Junction Box with Cover

26-943255

Truck Door Bottom Panel with Seal (15.5" x 98") for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood. Primer Finish
Comes only with bottom retainer and seal (installed)

620-00993

Linear Heater Kit 230V

Heater kit for slide gate operator 230V

PBTL-3-100

Key ONLY for PBTL-3 Z100 Sold per Key

Cut Key # Z100
Price for 1 key

.343-514-L

Cut-to-Length Torsion Spring .343 x 5-1/4" Left Hand Wound Blue/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-525-INSTALLED
If cones are required a filler must be added use part # FILLER

SNS1P6

Belden RG6 Co-axial "F" Male connector Snap-N-Seal

07-8058

LiftMaster Crank Link BG790

5001-WG-10-MOAK

Residential Side & Top Weather-Strip 10' Long Wood Grain Medium Oak with Screws

PVC wrapped
Painted aluminum retainer
Dual fin vinyl
Painted screws to match. 1 screw per foot
Sold by full case quantity (20)

1104-12FT-BRONZ

Residential Side & Top PVC Weather-Strip with cap 12' Long - Bronze (F)

Bronze rigid vinyl retainer with bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

801-300-001-00

Equinoxe Long Range Receiver 1-Door 433 MHz Pre-2016 *** To Extent of Inventory

1000 ft range
Old generation - prior to 2016

Programming Instructions Instructions de programmation

LVB620-11

Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

MOUNTSHAFT016A

Manaras Clutch & Hoist Shaft Kit for Opera-SH Nema 4/12 (OSHW)

Input / clutch shaft kit for Manaras Opera-SH N4/12

20-8100M-DC

LiftMaster Electric Motor for VSL 1 HP 90 VDC 1 ph

Replacement electric motor for VSL gate op.

4X20PO50

Devanco Loop 4' x 20' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

C16-32FHD

Bearing 1" x 2" Press Fit Heavy-Duty

Flanged ball solid steel bearing
Rating: 1 000 000 revolutions
Axial load: 150lb max
Radial load: 900lb max

19-5116

LiftMaster Trolley Roller Chain Pack #41 for 16ft Door

For 3/4 & 1 HP trolley operators

K20-1050C-2T

LiftMaster Electric Motor 1/2 HP 230V 1 ph CF

For gate op. SL580-5011

19-48047MN

LiftMaster Roller Chain #48 x 47 Nickel Plated

#48 x 47 pitch with master link

20001

Doorlec Brake Spring

Fits LJ/LJH

K74-33015

LiftMaster Electrical Box Replacement Kit L3 **to extent of inventory

For models T GT and GH L3

MGS20-B-2L-05

Miller Edge Sensing Edge Square Black 2-Wire Left Hand Outlet 5ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

MGS20-Y-2U-04

Miller Edge Sensing Edge Square Yellow 2-Wire Universal Outlet 4ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

CABLE_1/8SS5000

Cable 1/8" 7x19 5000' Stainless Steel ** Price on request

TC3-411

Lynx Commercial Trolley Op. 3/4HP 120V for 14' High Door with Brake Contactor

Sell Sheet

MOTOR403

Manaras Electric Motor 1/2HP 120V 1PH

Instant reverse
Medium-duty 1500 rpm
For OMJ/OMH

ST-PROFILE

Soft Touch Profile Sold per Foot

Yellow air-wave edge
Fits most standard 1-5/8" retainers
300 feet in a roll

CP-BRG-1

Lynx Bearing 1" *** Replaced by HW-BRG-1

2 in total on a MCJH

RA-AD-WKP-05

Lynx 5-btn Wireless Keypad AD455 372 MHz

Programming Instructions Compatibility chart

10-3209_GATE_BRKT

LiftMaster Gate Bracket

Fits SL580GL SL595GL and new IHSL24UL INSL24UL models

PRO-GH-10011-U

Micanan 1 HP 115V 1P Gearhead Operator N1 Eyes Monitored ECB

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

50027

Doorlec Maximum Run Timer with Base

H101L5-LH

LiftMaster Ind. Duty Hoist Op. 1 HP 115/230 VAC Logic 5 Left Hand W/Brake ***No Longer Available

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door.
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

Installation Manual Manuel d'installation Sell sheet Brochure

1003-6.5-PER-FT

Bottom U-Rubber 6.5" Black Sold per Foot

MOUNTSHAFT010

Manaras Hoist Shaft Kit for MJH (pre-1998)

Drawing

OPH-6232-CONT-L

Manaras Opera-H 1/2HP 208V 3Ph Contactor Left Hand

Installation Manual Sell Sheet

CONTACTOR008

Reversing Contactor Struthers Dunn 115VAC

MGH-6113-ECB-RH

Manaras 3/4 HP 120V 1P Jackshaft with Elect. Circuit Board Right Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

Installation Manual Sell Sheet

CP-PU-DRV-HDC

Lynx Drive Pulley 7/8" x 8" 5L HDC

7/8" shaft
8" diameter

1007-1-5/8-10

Aluminum Bottom Retainer Flat Fits Doors 1-5/8 to 1-3/4" Thick**Actual Length 10'1"

For door thickness of 1-5/8" to 1-3/4"

EL2000SS

LiftMaster Telephone Entry Access Control System Stainless Steel ***NLA

A high-capacity telephone entry access control system designed to complement virtually any gated community.
It is flexible enough to be used in apartment buildings condo complexes office parks and commercial sites.
features a 5-inch backlit LCD screen and clearly displays up to 4 lines with 20 characters per line making it a great choice for multi-tenant installations
Entry Codes allow for 2000 4-digit codes to be programmed. The codes can be time-restricted and/or use restricted. The codes can be split up any way you choose; 500 directory codes 1000 card codes 500 entry codes for example •Transaction Monitoring stores a maximum of 8000 transactions including date time identification and transaction type.
Activity Reporting gives property managers the ability to print database system and history reports.
Call Forwarding and Do Not Disturb schedules can be programmed for every resident.

.......more details

Installation Manual Programming Instructions Instructions de programmation Sell Sheet

TC134-16

Top Cap 1-3/4" 16 ft Black Box Qty Only ** To extent of Inventory

Sold in box quantities only
12 pieces per box

TC134-10

Top Cap 1-3/4" 10 ft Black Box Qty Only ** To extent of Inventory

Sold in box quantities only
12 pieces per box

71-B1PH

LiftMaster Internal Brake Kit w/Solenoid 120/240V 1PH for L5 Operators

Works with Logic 5 commercial operators and SL585/SL595 U and UL gate operators

MK-00098

Micanan Boot for Cut-Out Switch

CB18A500-KOR

Cable 1/8" 7x7 500' Galvanized Supreme

Galvanized cable 1/8" 7x7 500ft spool.
A higher quality cable than the Chinese cable.
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life

Comparison charts

T114

Manaras Trolley Track 14ft for 3/4HP & All APT models up-charge *Actual length 198"*

For models MGT/OTH/OTBH 3/4 hp only with Chain #41

1104-ASFT-9FT

Elton Aluminum Stiffener for 1104 9ft

Prevents the 1104 from buckling in the hot sun

2376.162_18.750

Whiting Torsion assembly .162 wire size 18" spring length 75" shaft

39-10541

LiftMaster Clutch Disc for SL595 (K39-10541)

4-11-7R

Roller 3" 10-Ball 7" Stem Nylon

Sealed bearing for long life in dusty conditions
7" stem (working length = 6 1/8")

MH00001

Micanan Bronze T-Bushing 3/8" ID

2 required per operator

50800P

LiftMaster Treadle Protection Plate **discontinued

97-75004

DOT-C2 Reflective Tape 150 ft x 2" W 11" White x 7" Red Pattern

DOT-C2 certified exceeds NHTSA requirements
Highly reflective even up to a 90 degree angle
Quick and easy to apply

S142ARNN924

Carlo Gavazzi Amplifier 24V

Processor controlled amplifier for one set of photoelectric sensors type MOFTR.
11-pin circular plug for easy connection.
8A SPDT relay output NPN/ PNP transistor output or alarm output.
Diagnostics for sensor test during operation.
Alignment help via LED or alternation of alarm output.
Level indication for dirt accumulation.

.......more details

Installation Manual

LC-36A

LiftMaster Light Curtain **discontinued

Must be used with a primary entrapment device and be installed along the vertical plane of the door.
Color-coded transmitter and receiver for easy identification.
Provides 36 in. of effective height coverage to increase the area of protection.
Multiple sets of LC-36A curtains can be mounted on a door providing coverage flexibility.
Maximum door width of 33 ft. ensures coverage for most commercial doors.
Eight (8) LEDs per side and 22 cross-beams produce an invisible curtain of infrared light for maximum detection capability.

.......more details

Installation Manual Manuel d'Installation Sell Sheet Connecting the lc-36A to a Non-LiftMaster Opener

27-48-320

Extension Spring 8' Door - 320 lbs Green

Single - Loop
27" long 48" stretch 320 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

27-48-140

Extension Spring 8' Door - 140 lbs Blue

Single - Loop
27" long 48" stretch 140 lb load
Sold individually
Rated for 10000 cycles

Spec Sheet

H12G06-SS

Hinge #6 x 12 gauge Stainless Steel **NLA

Manufactured with 12ga. Rust-Resistant Stainless Steel
Universal Design
Fits Most Overhead Sectional Doors
Priced Per Each

H12G01-SS

Hinge #1 x 12 gauge Stainless Steel ***NLA

Manufactured with 12ga. Rust-Resistant Stainless Steel
Universal Design
Fits Most Overhead Sectional Doors
Priced Per Each

K77-36541

LiftMaster Antenna

For various gate operators

ME120-BLK-E-5FT

Miller Edge 2-Wire Black End Outlet 5 ft Long

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details

Installation Manual Sell Sheet

9003-11FT-BLACK

Commercial Side & Top PVC Weather-Strip Reverse Angle 3" Track Bolt On 11' Long - Black

Black rigid vinyl retainer with black flexible vinyl insert.
Reverse angle bolt-on vinyl retainer.
Bolts onto reverse angle steel jamb.

Drawing

PRO-LH-5021U-LH

Micanan 1/2HP 230V 1P Medium-Duty Jackshaft N1 Eyes Monitored ECB Left Hand (PRO LHE) *** INDEF Delivery

Designed for use on commercial sectional doors with high or vertical lift
May also be used on small rolling grilles with max. 15 cycles per hour
Includes chain hoist
Includes solenoid brake
On board receiver with antenna
On-Board receiver holds up to 20 transmitters

.......more details

Installation manual Specification sheet

B119

Rolling Steel Fire Door Bottom Bar Slotted Angles Sold per Foot

4JW-RIGHT

Rolling Steel 3" Curved Cast Windlock 273004 RH

Windlocks are especially used on rolling steel doors and shutters to prevent "blow-ins" from severe storms or winds.
A wind lock is a small metal device that is attached to each slat.
Its primary function is to reduce the amount of friction that occurs between the actual door & the guiding panel.
When the wind is strong the roller door may be dislodged bent or misaligned from the guide.
With a windlock your door can operate efficiently despite wind load or pressure.
Windlocks are easy to add on to any existing rolling steel or shutter door

.......more details

SLT14-18P

Rolling Steel 3" Flat Slat 18-ga Primed

SLT14-22P

Rolling Steel 3" Flat Slat 22-ga Primed

340.115-CUT

Whiting Top Panel Tongue & Groove 11-1/2" h Cut to Exact Length

Primer only
Customer to specify exact length

342.115

Whiting Intermediate Panel Tongue & Groove 11-1/2" x 96" Price on Request

Standard size panel primer only

GH501-L5

LiftMaster Gearhead with Brake 1/2HP 115/230V 1P L5 ***No Longer Available

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting.
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

Installation Manual Manuel d'Installation Sell sheet Brochure

SL316COP

Copper Sleeve 3/16" 100 Sleeves per Pkg *price on request

Oval sleeves ONLY
Stops sold separately part # ST316COP

.375-5-1/4-LH-C

Torsion Spring .375 x 5-1/4" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .375 ID: 5-1/4" Length: 12 ft

.363-6-RH-C

Torsion Spring .363 x 6" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .363 ID: 6" Length: 12 ft

.273-3-3/4-RH-C

Torsion Spring .273 x 3-3/4" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .273 ID: 3-3/4" Length: 12 ft

.243-3-3/4-LH-C

Torsion Spring .243 x 3-3/4" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .243 ID: 3-3/4" Length: 12 ft

.234-1-3/4-LH-C

Torsion Spring .234 x 1-3/4" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .234 ID: 1-3/4" Length: 12 ft

.234-2-RH-C

Torsion Spring .234 x 2" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .234 ID: 2" Length: 12 ft

.218-2-RH-C

Torsion Spring .218 x 2" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .218 ID: 2" Length: 12 ft

.192-2-LH-C

Torsion Spring 192 x 2" x 144" LH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .192 ID: 2" Length: 12 ft

9723S19

Whiting Pull Strap 19" with Stainless Steel Buckle

K1D6597-1CC

LiftMaster Control Board with Heat Sink CSL24V & CSL24VH

Control board for CSL24V and CSL24VH gate operators
014D1058M

BK309

Jamb bracket J-09 #9 12 gauge

Sold by the piece
Height 4.25" Length 1.9" Width 2.45"
Bright zinc plated 12 gauge steel
2" long track mounting slot
manufactured to accept ¼” fasteners when attaching to the track and 5/16” to lag to the wall.

109B33

LiftMaster Trolley Belt Clip

SEL2641R433K8PM

Erone 800 User Receiver 433MHz

Multi-user receiver
800 two-channel transmitters + 7 master transmitters
Includes 1 master transmitter S2TR2641E2M for programming
12/24V AC/DC
Option: PC software kit # SEL2641KITP8 sold separately
1 NO relay + 1 NO/NC relay

.......more details

Installation manual Wireless System Chart

MGR20-Y-2U-05

Miller Edge Sensing Edge Round Yellow 2-Wire Universal Outlet 5ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

Installation Manual Sell Sheet

OGH-6115-ECB

Manaras 1-1/2 HP 120V 1Ph Gear Head Operator with Elect. Circuit Board

A heavy-duty worm gear industrial operator designed for use on industrial standard high and vertical lift sectional doors or rolling doors and grills.
Includes a self-engaging chain hoist for manual operation
25 cycles per hour 80 cycles a day
Hoist on right side standard can easily be moved to the left in field
Full overload protection
BRACKET112 must be used for wall mounting

.......more details

Installation Manual Sell Sheet

OTBH-6232-ECB

Manaras Trolley Operator 1/2 HP 208V 3 Ph with Electronic Circuit Board

The OTBH is a heavy-duty low headroom trolley operator
Designed for use on industrial standard lift sectional doors
It incorporates a drum-band type solenoid brake
25 cycles per hour 80 cycles per day
1/2 HP operators come with # 48 (410) roller chain

Installation Manual Sell Sheet

OHJ-6233-ECB

Manaras Heavy-Duty Jackshaft Operator 3/4 HP 208V 3 Ph with Elect. Circuit Board

25 cycles per hour 100 cycles per day
An Industrial duty operator featuring both the patented Hoist-a-Matic a self-engaging chain hoist for manual operation as well as a floor level disconnect
Specifically designed to motorize grills when a manual egress is required
Mechanical brake
Hoist on right standard
Full overload protection

.......more details

Installation Manual Sell Sheet

OHJ-6113-ECB

Manaras Heavy-Duty Jackshaft Operator 3/4 HP 120V 1 Ph with Elect. Circuit Board

25 cycles per hour 100 cycles per day
An Industrial duty operator featuring both the patented Hoist-a-Matic a self-engaging chain hoist for manual operation as well as a floor level disconnect
Specifically designed to motorize grills when a manual egress is required
Mechanical brake
Hoist on right standard
Full overload protection

.......more details

Installation Manual Sell Sheet

OHJ-6112-ECB

Manaras Heavy-Duty Jackshaft Operator 1/2 HP 120V 1Ph with Elect. Circuit Board

25 cycles per hour 100 cycles per day
An Industrial duty operator featuring both the patented Hoist-a-Matic a self-engaging chain hoist for manual operation as well as a floor level disconnect
Specifically designed to motorize grills when a manual egress is required
Mechanical brake
Hoist on right standard
Full overload protection

.......more details

Installation Manual Sell Sheet

OPJ-6434-ECB

Manaras Heavy-Duty Jackshaft Operator 1 HP 480V 3 Ph with Elect Circuit Board

An industrial operator designed for use on standard high and vertical lift sectional doors
Can also be used on rolling doors and grills
It incorporates a floor level disconnect mechanism for manual operation
25 cycles per hour 100 cycles per day
Continuous-duty single phase capacitor start or 3 phase motor open drip proof
Mechanical brake

.......more details