Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MK-00522

Micanan Relay 24 VAC 8-Pin Plug-In

SD105L5-RH

LiftMaster Heavy-Duty Slide Door Operator 1 HP 575V 3PH Right Hand (Must include hardware box)

Perfect for split and sliding doors involved with industrial applications.
It is installed above the door and corresponds with the direction the door will be traveling.
Comes equipped with an emergency disconnect and for manual lifting in an emergency and automatic reconnect.
The new logic 5 commercial operators come with MyQ Technology built in. * 828LM required
Built In Security+ 2.0 radio receiver
Solenoid brake included
Trolley roller chain #41 on all SD operators
Door speed: 11-12 inches per second

MD-00487

Micanan Roller Chain #60 Stainless Steel 10' Pack

PRO-J-10083-U-LH

Micanan 1HP 208V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

.312-514-L

Cut-to-Length Torsion Spring .312 x 5-1/4" Left Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.306-2-L

Cut-to-Length Torsion Spring .306 x 2" Left Hand Wound Red

Priced per inch
For factory installed cones priced seperately - use part no. C-200-INSTALLED

BOLLARD_4'

Bollard 6" Dia. x 1/4" x 48" High Capped (w) Base Yellow Powder Coat

6" Diameter 1/4" Steel Wall 48" High Base Plate is 10" x 10" x 1/4" Thick 5/8" Holes for Mounting Powder Coated Yellow

2X4PO50

Devanco Loop 2' x 4' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

PRO-J-7583-U-RH

Micanan 3/4HP 208V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

LMWETXU

LiftMaster Wireless Edge Transmitter Monitored

Connects to wireless edge receiver using low-energy Bluetooth transmission
Sensing distance up to 130 ft
Transmitter accepts up to 2 wired resistive edges
Battery life 2 years
NEMA 4X rated
Compatible with LMWEKITU Wireless Edge Kit and L50 and S50 Monitored Resistive Edges

.......more details

Installation manual Manuel d'installation Product Guide Guide de produit

PRO-J-5053-U-LH

Micanan 1/2HP 575V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

PRO-J-5081-U-LH

Micanan 1/2HP 208V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

PRO-GT-10083-U

Micanan 1HP 208V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-10011-U

Micanan 1HP 115V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-10081-U

Micanan 1HP 208V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

NUT-14-SS

Nut Stainless Steel 1/4"-20 Flanged Serrated Hex

PRO-GT-5011-U

Micanan 1/2HP 115V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

ALUM-507

Aluminum 24" x 100' Spool Tan / Tan # 507

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 507
Reverse side is #431 Bright White

Colour chart

ALUM-5P6

Aluminum 24" x 100' Spool Iron Ore / Minerai de Fer # 5P6

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 5P6
Reverse side is #431 Bright White

Colour chart

.393-334-R

Cut-to-Length Torsion Spring .393 x 3-3/4" Right Hand Wound Orange

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

PRO-APTB-5083-U

Micanan 1/2HP 208V 3P Apartment Trolley Operator With Brake N1 Eyes Monitored ECB

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-10023-U

Micanan 1 HP 230V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-10011-U

Micanan 1 HP 115V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-7581-U

Micanan 3/4HP 208V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-7543-U

Micanan 3/4HP 460V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-7523-U

Micanan 3/4HP 230V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-7511-U

Micanan 3/4HP 115V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-T-5025-U

Micanan 1/2HP 220V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

SC-6

Wheel Chock SC-6 Aluminum

Excellent Surface Grip on Tire and Ground
Lightweight Aluminum
Size: 6" wide x 6-1/2" long x 6" high

68-9U

Wheel Chock 68-9U Pyramid Rubber with U Handle

Handles for chain fastening
Long Lasting 80 Durometer rubber
Size: 8" wide x 9" long x 6" high

31337

Doorlec Idler Sprocket with Oilite bushing 50B12 for a 1" Shaft

RELAY039

Manaras Relay 3-Pole 24VAC

BPPB1759

Garex Bottom PVC Moulding for 1 3/4" Door White U shaped 108"(9')

STRUT-2-1/4-10'

Door Strut 2-1/4" Hemmed 10 ft Long

Reinforcement bar 2-1/4"
Electro-Galvanized
22-GA

R5212

Pulley 5" Zinc Plated Clevis Pulley with Strap ** To extent of inventory

CP-IDLER-ASSY-MR

Lynx Front Idler Assembly Chain TC3

RATCHET_BAR

Rachet Bar for Holdown Assembly

31D380

LiftMaster Sprocket Cover

Sprocket Cover Replacement Kit for use with various LiftMaster® and Chamberlain® Chain Drive Garage Door Openers

HRB-10

High Riser Bracket for 7" Above Dock or Higher 10"

High Riser 10" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

HRB-9

High Riser Bracket for 7" Above Dock or Higher 9"

High Riser 9" Riser Bracket for 7" Above Dock Door or Higher
Also available with 2" 3" & 4" Extensions or with Cutout - Call for More Information

E/BLOP/150

Automatic Systems Safety Edge for BL229 14'-9" (EABLOP/150)

MK01065

Micanan Light Duty Resistor 2 OHM 25W c/w Wire Leads

15480

Doorlec Heater Strip 175 W 575 V

MR-00021

Micanan Trolley Chain Drive # 41 792 Links for 3/4 1 HP 14ft High Door

T

Molded Rubber Bumper Black 22" L x 10" W x 12" W 3" Projection Centered Reflector 3-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 3 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

DBE-20

Molded Rubber Bumper Black 20" L x 4 1/2" W 3" Projection 4-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles.
Bumper comes with 4 pre-drilled countersunk mounting holes drilled to accept 3/4" anchor bolts

.......more details

LVB1220-11

Laminated Bumper Black 12" Projection Vertical Installation 20" L x 11" W Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB1210-36

Laminated Bumper Standard Black 10" x 36" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1210-24

Laminated Bumper Standard Black 10" x 24" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1010-36

Laminated Bumper Standard Black 10" x 36" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1010-24

Laminated Bumper Standard Black 10" x 24" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB910-36

Laminated Bumper Standard Black 10" x 36" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB824-11

Laminated Bumper Black 8" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB820-11

Laminated Bumper Black 8" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB810-36

Laminated Bumper Standard Black 10" x 36" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB420-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

Drawing

TB412-18SF

Steel Faced Laminated Bumper Black 12" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

Q080

LiftMaster Dolly Latch Kit K75-50138

For Liftmaster trolley operator HCT

K75-36914

LiftMaster Electrical Box Cover APT T GT SD GSD GH - L5

LB412-14SF

Steel Faced Laminated Bumper Black 12" x 14" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB636-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TVB624-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 24" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TVB620-11SF

Steel-Faced Laminated Bumper Black 6 3/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LLB620-22SF

Steel Faced Laminated Bumper Black 6" Projection L-Shaped 20" x 22" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.

.......more details

LB612-24SF

Steel Faced Laminated Bumper Black 12" x 24" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

8010

LiftMaster DC Chain / Cable Drive Garage Door Opener ***Discontinued***

Customized DC Motor with soft start/stop action.
Chain/cable square steel rail (SSR) system for efficient operation and standard performance.
Security+2.0 increases remote control range and reduces interference for consistent operation.
PosiLock® electronically protects against forced openings.
The Protector System® invisible light beam auto-reverses the door if there is an obstruction.
Comes with: Door Control Button (883LM) 1-Button Remote Control (891LM)

.......more details

LVB630-11

Laminated Bumper Black 6" Projection Vertical Installation 30" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-12

Laminated Bumper Standard Black 12" x 12" 6" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB412-14

Laminated Bumper Standard Black 12" x 14" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB410-12

Laminated Bumper Standard Black 10" x 12" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

PRO-GHC-30053

Micanan 3 HP 575V 3P Gearhead Operator No Controls

Specification sheet

BPPVCT

Garex PVC White Transition Moulding 289" #3764

Universal garage door panel adapter molding
Use on any 1-3/4" door
Allows a Garex panel to be used as replacement on any brand door
24' lengths only can be cut for transport

34115

Doorlec Awning Pulley 194 x 1"

Used on model LDJ & LDJ-3

R4

Erone Radium 4-Channel Key Chain Transmitter 433MHz

Designed for the control of automatic closing systems and anti-burglar systems thanks to its very high security coding system (KeeLoq® Hopping code).
The code sent by the transmitter changes at each activation avoiding any scanning and copying risk.
A special algorithm allows to keep synchronized transmitter and receiver.
Range up to 250 m (820 ft)
Ergonomic rugged & durable
Battery: Two 3V lithium battery (CR2016)

.......more details

K79-32927

LiftMaster Control Board Autogate *** Not Available

Replacement control board used in various Autogate Operators.
Autogate is a gate operator manufacturer that utilizes LiftMaster control boards in their operators
Formally AG001

MK-00030

Micanan Transformer 115V-24V-40VA

38877R.S

Genie Non-Configured Circuit Board

Replaces the following models: 38001R1.S 38001R2.S 38001R3.S 38001R4.S 38513R.S 38514R.S 37470R1.S 37470R2.S 37470R3.S 37470R4.S 38334R1.S 38334R2.S 38334R3.S 38334R4.S
Compatible with Series II Controls and comes with only the circuit board
In order for this kit to function properly it is important that customers know the model of their opener.
If unsure as to what resistor needs to be remove refer to the instructions that came with the unit

Z9211-3

Stationary Cone Tool 3-3/4"

Easily dislodges the cone from the torsion spring

RP-TRF-110-2415VA

Lynx Transformer 110/24 15VA *** NLA

For old 455 Automatic Doorman opener

MF00011

Micanan HH.H. Bolt 3/8" - 16 UNC x 3/4" Long

Used on PRO-GHC
10 required per operator

LVB620-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

MG00041

Micanan Spring Clip 7/8" ID Sold Individually

2 required per machine

BB-1

Rubber Button Cover Black for 3BLM PBS

Rubber button cover only

T-50-H

FL-Heddolf 1-btn Transmitter ID220-1KA-311 MHz ** Discontinued

Keystone-Heddolf single button FL T-50 compatible remote
9 dip switch format
9V battery and metal clip included

BINS-SANDSTONE

Utility Bin Heavy-Duty Stackable Sandstone *** No Longer Available

Usable in virtually every environment both indoor and outdoor and they are made from Polypropylene which will not fade in the sun
Outside dimensions: 16.75" L x 10.75" W x 6.55" H
Inside dimensions: 12.15" L x 8.375" W x 6.5" H
Sold per bin

MD00002

Micanan Bevel Gear 20 Tooth 5/8" ID

Comes with keyway and 2 set screws
Used on PRO-GHCW

MK-00646

Micanan 9" Coax Cable for On-Board Receiver

COLLAR004

Manaras Collar 5/8"

K1D8388-1CC

LiftMaster Main Control Board Linear Actuators for UL325

This replacement board is compatible with the following models: LA500U LA400U LA412U
Same as 001D8388-1CC
Sticker on board references 001D9040-1CC

.363-334-R

Cut-to-Length Torsion Spring .362 x 3-3/4" Right Hand Wound Green/White

Priced per inch - cones sold separately
For factory installed cones use part no. C-375-INSTALLED

VWS-34-MED-OAK

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Medium Oak

Pan head

VWS-34-SANDSTONE

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Sandstone

Pan head
S point

2650-112-11

Linear Cold Weather Package HSLG 230V

Factory Option 2650-112-11 Cold Weather Package for 230-volt HSLG
Package includes: Arctic Oil Heater Cogged Belt
This factory option is only available for purchase when buying your gate operator.