Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MV-00296

Micanan Wireless Push Button Station OCS for Logic 10.0

Used only on Logic 10.0 program 3.2.5

K1D8387-1CC

LiftMaster Expansion Board UL325

Compatible with various LiftMaster® DC Swing and Slide Gate Operators; manufactured after 2016.
This board is backwards compatible for older second generation units but will require UL325 Entrapment Protection System and Photoelectric Sensors or Edge Sensors.

LIMIT023

Manaras Single Limit Switch with 46 degree Lever

Single limit switch (SPDT) used to stop the door at top and bottom or as disconnect switch
Unimax
Snap-action

26CW94525-CUT

Truck Door Intermediate Panel (15" x Cut-to-Size) Painted White for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white

MK00542

Micanan Emerson Motor Capacitor 1/2HP 110V 324-389uf with Resistor *** No Longer Available

For 1/2 Hp 110V operators

41B0873

LiftMaster Safety Sensor Sunblocker Kit Works With 41A5034 and 041-0136

This complete kit is used to shield sunlight and prevent accidental reversal of garage door from sunlight shinning directly into the safety sensors
Works with 41A5034
Same as: 041B0873 41B873

K1D8284-1CC

LiftMaster Main Drive Board 1 Ph

50-ALMARM-DOT

LiftMaster 15 ft Aluminum Barrier Arm Square White Aluminum with Red/White Retro-Reflective DOT Tape

Used on BG770
Arm adaptor included
15' x 2.5" square arm
Replaces 50ALUMARM

VBELT_5L370

Manaras VBelt 5L 37" - repl. by B34

5L370

30257T

Genie Coupler Screw Drive Units

Used for attaching the screw of Genie screw drive rail to the motor head.
This coupler is made to break away if the door hits a hard obstruction thereby protecting the motor.
If the motor of the screw drive Genie runs but the screw is not turning this coupler needs replaced.
To check and replace that part remove the two screws holding the rail to the main power head
Mounts on rear of opener rail and fits in motor head.

TRACK-GUARD-48

Track Guard 48" Tall Safety Yellow With Base Sold as a Pair

Provides impact protection to vertical track
45° angle flange adds strength protects from side impact.
7-gauge steel construction powder coated safety yellow for high visibility.
1/4” foot plate drilled with slotted holes for three 1/2” anchors.
Wall flange drilled with slotted holes for four 3/8” anchors
Includes: 60-5094 (right) and 60-5095 (left) sides

.......more details

10-1036-4

Whiting 2" Nylon Roller 5" Stainless Steel Shaft for Truck Doors

A Whiting original part
Stainless steel bearings stainless steel shaft

MB-03102

Micanan Electric Motor Only 1 HP 230/460V 3PH Base Mount O.D.P FR56

Base mount motor fits: T TB APT J EJ H EHJ HHD SD

25-10105

Truck Door 1" Steel Roller 3.25" Shaft Length for Todco Roll-Up Doors

Zinc plated Hardened shaft and raceways
Seven roller ball design

CPS-UN4G

LiftMaster Commercial Protector System Thru-Beam Eyes NEMA4 Black

Waterproof photoeyes.
Monitored Thru Beam Photocell
For direct connect on HCT

CH100

Contact Cleaner and Lubricant 325g

Cleans both electrical and electronic parts.
Cleans dries and leaves a thin protective film.
340g / 11.5 oz spray can
12 cans per case

Safety data sheet Fiche de données de sécurité

MV-00295

Micanan Fraba Nema 4/4X RAY-RT-HD with Reflector

Monitored Retroreflective photocell
Sensing distance: 50 ft
Includes bracket and long range reflector

MD00420

Micanan Flex Coupling Lovejoy 3J x 3/8"

41D7742-5

LiftMaster Travel Module Kit 3/4 Hp

A one piece travel module replacement kit.
Compatible with 3/4HP LiftMaster® Models 8557 & 8587 and various AC chain and belt drive garage door openers
Same as 041D7742-5

FRONTIDLER010

Manaras Front Idler Assembly #41

LEVER051

Manaras Brake Lever MGH C-1 Galvanized

SPRING026

Manaras Trolley Arm Disconnect Spring MGH

CP-BRC-12

Lynx Resettable Circuit Breaker 12 AMP

Used on MCJH 3/4 hp 120V operators

SPR41B36X1.5

Sprocket 41B36 1.5" Bore 3/8"x3/16" keyway

JY-10

Devanco Solvent & Degreaser 400g

General purpose solvent and degreaser
Contains natural citrus oils. Cleans oily greasy and dirty surfaces.
Dries quickly and leaves no residue.
Approved by CFIA.

Safety data sheet Fiche de données de sécurité

.243-258-R

Cut-to-Length Torsion Spring .243 x 2-5/8" Right Hand Wound White/Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

BCH751L5-LH

LiftMaster Hoist Op. with Carwash Mod. and Brake 3/4 HP 115/230 VAC Logic 5 Left Hand ***Replaced by CRBH751-LH

Industrial Duty Hoist Operator with Damp Environment modification.
Comes with either CPS-UN4
Brake installed on operator

Installation manual Manuel d'installation Sell sheet Brochure

OTBH-6232-APT-C

Manaras Trolley Operator 1/2 HP 208V 3 Ph Apartment Model with Contactor

The OTBH is a heavy-duty low headroom trolley operator
Designed for use on industrial standard lift sectional doors
It incorporates a drum-band type solenoid brake
30 cycles per hour up to 100 cycles per day
APT model incorporates pillow block bearings on input shaft
A 4L/A v-belt

.......more details

Installation manual Sell sheet

C-24X12-134-W

Thermal Window 24" x 12" for 1-3/4" Cedo Door White

For 1-3/4" thick door

2806.156.195

Whiting .156 x 2-3/16 x 19.5" Roadside with Cones

ALUM-547

Aluminum 24" x 100' Spool Sable / Sablon # 547

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 547
Reverse side is #431 Bright White

Colour chart

ODCC-SPEC.ORDER

Wayne Dalton Special Order *** Price by Quote Only

Misc. code for all special order items

PRO-LH-5011R-RH

Micanan 1/2HP 115V 1P Medium-Duty Jackshaft with Contactor Right Hand (PRO LHR)

Designed for use on commercial sectional doors with high or vertical lift
May also be used on small rolling grilles with max. 15 cycles per hour
Includes chain hoist
Includes solenoid brake
No longer available in contactor model (2017)

Installation manual Specification sheet

ULTRA-II-D-TEK

EMX Industries Plug-in Loop Detector (2663-1)

Features a slim design that is compatible with most gate operators that require a dry contact relay input.
No harness required; comes with terminal screw adaptor
ULTRAMETER™ (displays optimum sensitivity setting / diagnostic aid)
Frequency count/reset switch
10 sensitivity settings
Loop diagnostics

.......more details

7001-7-CHARCOAL

Commercial Side & Top Weather-Strip 7' Long - Charcoal 7001-HH (H)

Charcoal galvanized steel with charcoal dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

9-24-1

Lynx BarLock Mounting Plate

Assembly Manual

6976.182.23.440

Whiting Single Spring Balancer Assembly .182 x 23" x 44" Shaft

1104-7FT-LT-BNZ

Residential Side & Top PVC Weather-Strip with cap 7' Long - Light Bronze (F)

Light bronze rigid vinyl retainer with light bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

19863R

Genie Clip and Collar Rail Connectors

For Genie screw drive units having split rails use a collar and spring clip to join the 3-piece screw.
Complete collar and clip set for one 3-piece rail.
Compatible with all screw drive Genie garage door openers
Set of 2 clips and 2 collars
Same as 19806A04 and 19807A04

KPW5

LiftMaster New Wireless Commercial Keypad 5-Code Sec.+2.0

Designed to work exclusively with Security+ 2.0
5 permanent PINs and 10 unique temporary PINs ideal for residential and small commercial applications; unique temporary PINs can be set for 1 to 9 uses
Allows for removal of a single PIN while maintaining full access for other users
High-impact polycarbonate front cover; perfect for rugged outdoor environment
Blue backlit metal keypad makes it easy to use under low-light conditions
Electronics are fully sealed and meet NEMA 4X water protection requirements

.......more details

Programming instructions Instructions de programmation Sell sheet Brochure Compatibility chart

MET-14500C

Cable Tie Metal Tooth 14" 50 LB Black 100/Bag

M4A

Safety Inertia Brake 1-1/4" Bore 3576 Torque PCM4AP

Provides a bearing to support the shaft and prevent the fall of a door if sudden acceleration occurs.
Ideal for commercial and industrial use; specifically with rolling shutters and rolling doors.
Fits 1-1/4" shaft
Normal Torque: 3576 lbf.in
Locking Torque: 17516 lbf.in
Made in Italy

.......more details

Reference manual Technical data Sell Sheet

LVB620-11

Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

CPS3-N4

LiftMaster Option Card with CPS-UN4 Eyes for applications requiring 2 sets of photocells

For applications requiring two sets of photoeyes in a damp location
Range up to 45ft water dust and corrosion proof eyes (Nema 4x rating)
Works with Logic 3 4 5 Commercial Operators
Includes Durable steel brackets - floor or track mounting
Kit Inludes one set of CPS-UN4 and one CPS3 card ( CPSIII )

PBTL3-BLACK

Replacement Button Only - N/O Open / Close Black

N/O switch and rubber cover for PBTL-3

226-9312

Lithium AA 1.5V Battery

Used in IG2 photo eyes

4X20PO50

Devanco Loop 4' x 20' pave-over 50' lead-in

Ideal for use on with gravel driveways or surfaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

Installation instructions Instructions d'installation Spec Sheet Brochure Loop Placement Guide Guide de positionnement des boucles

ALUM-801

Aluminum 24" x 100' Spool White / Blanc # 801

20% thicker than the aluminum sold in retail stores (0.022" )
Aluminum on the reverse side
Gentek # 801

Colour chart

MB-02002

Micanan Electric Motor Only 3/4HP 110/220V 1PH TEFC

Base mount motor fits: TW TBW JW HW HHDW SDW

5-30-6

3" Vertical Track 12-GA 11'-4" (12' door) Sold per Pair

CS303-C-1

EMX Car Sense Vehicle Detector Control Unit *** Replaced by LRS-C1

The CarSense™ 303 features advanced 3-axis magnetoresistive sensing technology.
The sensor measures Earth’s magnetic field and responds to disturbances caused by ferrous objects.
The CS303 combines this exciting new technology with a fieldproven hardware platform to produce a high-sensitivity compact and cost-effective solution for reliable vehicle detection.
Three sensing elements provide magnetic field measurement in the X Y and Z axes improving detection sensitivity.

JRGX114

Chain Hoist Jack Shaft JRG V2 1-1/4" Shaft Torque Force (126690)

Jack Shaft Mounting plastic guide 4.5:1 reduction
Gear drive
Fits 3-3/8" minimum offset
Includes: 26' of galvanized hand chain - doors higher than 15' require additional hand chain
1 chain keeper
2 shaft collars

.......more details

Sell sheet

22210

Push Button Station 3 Oval Buttons O/C/S Flush Mount ** discontinued. To Extent of Inventory

Three button wall station Open/Close/Stop
NO contacts on the Open and Close buttons
NC contact on the Stop button
Stainless steel surface plate
Flush mount

SPECIALPANEL001

Manaras Complete C-Box Special Order

Includes limit system limit shaft.

FHKS3D-74

Stainless Steel Face Hardware Kit 3" Track Double End Stile 4 Panel 7 Sections

Kit includes: Top & Bottom fixtures Center hinges End hinges and Hinge screws.
304L rust-resistant stainless steel
12 gauge

Q074

LiftMaster Coupling (3/4 x 5/8) 3 pcs K75-50130

Fits model HCT
Same as K75-50130

FL-T50

FL-Heddolf 1-Button Dip Switch Remote FL 311MHz *** Discontinued.

ID220-1KA Heddolf remote
9V battery & metal clip included

K72-33192

LiftMaster Limit Shaft Kit

For: NEMA 4 & 4X for H J HJ GH GT T & APT Operators
Shaft measures 12" in length
Compatible with Logic 4 and Logic 5 operators

ST-CLEAR-TUBE

Soft Touch Clear Tubing Sold per Foot

RA-AD-WWS-MULTI

Lynx Wireless Wall Station AD455 372 MHz

Wireless for easy installation anywhere
Controls door open-close light on-off
Programmable pet opening (Opens to a pre-selected height of 6"-30")
Vacation Slide-Lock: Disables remote transmitters keyless entries and wall stations.
10-second closing safety delay
Transmitter program button

.......more details

Programming Instructions Compatibility chart

RA-AD-T3

Lynx 3-btn Transmitter AD455 372 MHz

UL325
Works on the new Lynx operators
For 3 doors

Programming Instructions Compatibility chart

25-60503

Truck Door T-Style Ramp Handles Curbside (Right)

Black plastic construction
Cross ref.: 39504-2

22306

Programmable 7-Day / 24 Hr Timer

7FT-BELT-SKYLNK

SkyLink 7 ft Rail Belt

CP-LX225

Lynx Enhanced Relay Board

7001-WG-16-CO

Residential Wood Grain Side & Top W/S Cherry Oak 16' Long - Painted Screws to Match

Cherry Oak retainer with Cherry Oak vinyl
PVC Wrapped
Steel is Notched on Both Ends for Easier Installation
Economical
Dual Fin Vinyl
Painted Screws to Match

.......more details

RS10295

Roller 2" Steel 9-1/2" stem 10 ball Hurricane Roller

High strength steel roller designed for hurricane applications
Wheel Diameter: 2"
Steel tire Stem made from alloy steel
Rated: 15000 cycles for a 12'h door
Load rating: 75 lb
Box qty: 100 Box weight: 62 lbs (2-9-1/2-10 steel)

.......more details

G658056

LiftMaster Counterweight for BG790 Arm

For 17' gate arm and up
For use with various LiftMaster® Barrier Arm Gate Operators (BG790) and Perimeter Access Solutions.
Also known as: 108056 088056 10-8056 G658056 G088056 10-8056M

MD-00003

Sprocket 41B36 x 1" Bore 1/4" Keyway

2 set screw 5/16

29-ABC-15

LiftMaster Fuse 15A

For VSL595 gate operator

1458W

Fasteners Self-Tapping Stainless Steel Hinge Screw with Washer 1/4" x 5/8"

400 Series Stainless Steel
Self Threading
Washer Head with Rubber Seal
Use with Stainless Steel Garage Door Hinges

VBELT_4L370

Manaras VBelt 4L 37"

Used on MJH models from 1980 - 2000

MA117

LiftMaster Counterweight for Arms 15ft & Up

BRAKE013

Manaras Band Brake Assembly Kit OSH

Installation Manual

SLT14-22P

Rolling Steel 3" Flat Slat 22-ga Primed

M-VERSION

Manaras Monitored Entrapment Protection Option Upgrade Mont Thru-Beam + N1 Eyes

Upgrades added when purchasing a commercial operator

.375-5-1/4-RH-C

Torsion Spring .375 x 5-1/4" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .375 ID: 5-1/4" Length: 12 ft

.283-3-3/4-RH-C

Torsion Spring .283 x 3-3/4" x 144" RH Coated ** Price by Quote Only

Black Oxide coating
Wire size painted on spring
Wire size: .283 ID: 3-3/4" Length: 12 ft

MK00650

Micanan UPCHARGE for N-4 Photocells in Lieu of Nema-1 Reduction for N1 Included. **Obsolete Repl by MK00697

In lieu on the standard Nema-1 photocells supplied with the operator

Installation Manual

MGR20-Y-2U-04

Miller Edge Sensing Edge Round Yellow 2-Wire Universal Outlet 4ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

Installation Manual Sell Sheet

OGH-6115-ECB

Manaras 1-1/2 HP 120V 1Ph Gear Head Operator with Elect. Circuit Board

A heavy-duty worm gear industrial operator designed for use on industrial standard high and vertical lift sectional doors or rolling doors and grills.
Includes a self-engaging chain hoist for manual operation
25 cycles per hour 80 cycles a day
Hoist on right side standard can easily be moved to the left in field
Full overload protection
BRACKET112 must be used for wall mounting

.......more details

Installation Manual Sell Sheet

OGH-6112-ECB

Manaras 1/2 HP 120V 1Ph Gear Head Operator with Elect. Circuit Board

A heavy-duty worm gear industrial operator designed for use on industrial standard high and vertical lift sectional doors or rolling doors and grills.
Includes a self-engaging chain hoist for manual operation
25 cycles per hour 80 cycles a day
Hoist on right side standard can easily be moved to the left in field
Full overload protection
BRACKET112 must be used for wall mounting

.......more details

Installation Manual Sell Sheet

801-300-002-01

Equinoxe Long Range Receiver 1-Door Industrial Enclosure 433 MHz New Generation

1000 ft range
2016+
This receiver will accept 8 Equinoxe O/C/S remotes
Nema 4

Programming Instructions Instructions de programmation

OTBH-6433-1-ECB

Manaras Trolley Operator 3/4 HP 480V 3 Ph with Electronic Circuit Board

Heavy-duty low headroom trolley operator designed for use on industrial standard lift sectional door
25 cycles per hour 80 cycles per day
It incorporates a drum-band type solenoid brake.
Tracks are an extra 36 lbs per track
3/4 HP & 1 HP operators come with #41 full roller chain

Installation Manual Sell Sheet

OHJ-6113-ECB

Manaras Heavy-Duty Jackshaft Operator 3/4 HP 120V 1 Ph with Elect. Circuit Board

25 cycles per hour 100 cycles per day
An Industrial duty operator featuring both the patented Hoist-a-Matic a self-engaging chain hoist for manual operation as well as a floor level disconnect
Specifically designed to motorize grills when a manual egress is required
Mechanical brake
Hoist on right standard
Full overload protection

.......more details

Installation Manual Sell Sheet

20418R

Genie Limit Switch Lead Wire Brown

Brown - Used to connect down limit to sequensor
For Screw drive models

AK-21

Linear Interior Digital Keypad***to extent of inventory

The keypad is housed in a rugged plastic enclosure and is designed to be mounted in a standard single-gang electrical box. The die-cast keys have bright easy-to-read yellow graphics.
It is supplied with four different plastic snap-on mounting bezels to customize the look of the keypad. The satin-chrome bezel comes factory installed on the keypad. The white ivory & bronze bezels are packaged separately.
Up to 480 entry codes from 1 to 6 digits in length can be programmed. They can activate either or both of the relay outputs.
Relay #1 has a 5 Amp capacity. Relay #2 has a 1 Amp capacity. The relays can be set for timed or latch-on/latch-off toggle operation per each individual entry code.
The on or off toggle state of a relay is maintained even after power interruption. When power is restored to the keypad each relay will assume the state it was in when power was removed.

Installation Manual

OPH-6112-CONT-R

Manaras Opera-H 1/2HP 120V 1Ph with Mechanical Contactor Right Hand

A heavy-duty industrial jackshaft operator.
For use on Standard High and Vertical Lift sectional doors.
Can also be used on Rolling doors or Grilles.
Comes with a self-engaging chain hoist for manual operation.
Clearence: side room required 15"
25 cycles per hour 100 cycles per day

.......more details

Installation Manual Sell Sheet

MA025

LiftMaster Padded Barrier Arm Yellow 12ft

For use on Mega-Arm gate operator

Additional arm accessories

29-10338

LiftMaster Capacitor 70uf 230V 60Hz

For models: MJ5011 MH5011 HMJ5011 MT5011 and BMT5011

7001-14-BLACK

Commercial Side & Top Weather-Strip 14' Long - Black (Code B)

Black galvanized steel with black dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.

029C98200-PRIMR

W-Style Complete Repl. Door Primer only

Primer only no stainless steel package.
For doors upto 98" wide x 100" h
Fully assembled door manufactured to exact size with all tracking and spring operator assembly
Price varies according to size

MK-00002

Micanan Timer Module (2 wire)

719323

FAAC Steel Rack for Model 844 Operator

348.000

Whiting Tongue & Groove Bottom Panel Assembly with #77 Lock Made to Order. **Quote Only

15-1/2" x 96" standard size panel.
Extra wide panels will carry an additional charge
Primer only

111854.0002

Overhead Logic Board for RSX 3/4 & 1 Hp

Description: KITPCB1PH3/4-1HPSX/HXUL10
For RSX ad RHX models 3/4 & 1 Hp Single phase operators

MK500GS

LiftMaster MiniKey Stand-Alone Keypad System ** No Longer Available

Self-Contained Keypad System for Door and Gated Entrances
500 Code capacity
Grained stainless steel Surface Mount
Dimension: 4-1/2" H x 4-1/2" W x 3-1/2" D
Same as SN7000255
Sentex Keypad

.......more details

Installation Instructions Programming Instructions Sell sheet

HOMELINK-REPTR

LiftMaster HomeLink Repeater Kit ** same as 855LM

All 2006 or older vehicles require a repeater kit installation
In 2007 and newer if the HomeLink does not program with opener install a repeater
The remote supplied in the repeater kit must be kept for future programming and is NOT to be used as a garage door opener remote