Devanco Canada - Get The Right Garage Door Opener‎ and Parts

Garage Door Opener Parts

Marantec / Garaga

M8-705

Marantec Photoeyes 69190 / 97246

Works on all Marantec units
Includes brackets hardware and wiring
Same as item #86850 97246 used to be M4-705

Installation instructions

8030234

Marantec Chain Connector Kit

Works for all Marantec Chain Drive Openers
For models: Mac Lift M4500M4700Q7500Q7700 M4500e M4700e
Includes two connector pieces and four screws
Not for use on the heavy duty rails used by Q7900 & M4900e

89493

Marantec RPM Sensor with Wire Harness

For use on M-line/Q-line/EOS models

91568

Marantec Sprocket Holder Assembly for Chain Rail

Compatible with Marantec Chain Standard Rail.
Same as #8030339 (old part number)

95358

Marantec Front Idler Assembly

Complete Roller holder assembly for ML-Series rails
Used for belt and chain drive opener rails
Same as # 8030432

98875

Marantec Shark Tooth Position Reference Tab Chain Rail

For chain rails.
This part is installed inside rail on the actual chain.
This part works with the reference switch to determine the open & close limits of the garage door.
Reference switch part # 104083

97799

Marantec Shark Tooth Position Reference Tab Belt Rail (96834)

Same as part number 96834
For belt rail

Replacement Instructions

104083

Marantec Reference Switch for Belt and Chain Rails

This part works with the positioning tab and motor to determine the open & close limits of the actual garage door.

118798

Marantec Trolley Assembly (Slider)

Replaces #8030177 and #803178
Replacement trolley assembly for chain & belt rail assemblies
Fits Marantec opener models: M4500M4500eM4700M4700eQ7500Q7700
Works for 7' 8' & 10' high doors (red pull cord rope can be adjusted to length accordingly)
Note: will not work for the Heavy Duty (2mm-14ga.) rail assembly
Same part number as 91570

.......more details

97798

Marantec 2 Piece Logic Board with Terminal Strip for EOS Models

For use on Easy Operating System (EOS) units 4500E 4700E and M50.
Includes the terminal strip for direct replacement of boards that had a power surge or burned out.
The marantec old model number was 78914 it is now 97798.

Programming Instructions

84284

Marantec Logic Board for Non-EOS Models

For use on M Line- M-4500 and M-4700 models.
For use on Q Line - 7500 and 7700 models.
For use on Martin DC 3500E and DC 3700E models.
Replaces 8054216. Special programming needed. Instructions included

91567

Marantec Sprocket Holder Assbly Standard Belt Rail

Compatible with Belt Standard Rail
For Marantec belt opener models: Synergy 260 Synergy 270 Synergy 280 Synergy 360 Synergy 370 Synergy 380 Synergy Solo M50 M55
Not for use on the heavy duty 1.2mm - 18 gauge rails
Measures 5"x2-3/4"x1-1/4"

88824

Marantec Sprocket Holder Assbly For Heavy Duty 1.2mm Belt Rails Only

Compatible with Marantec Heavy Duty (1.2mm - 18 gauge) 2-Piece & Standard Belt Rail
Compatible with Marantec models: LC1000 M4500 M4500e M4500eI M4700 M4700e M4700eI M4900e Q7500 Q7700 Q7900 Synergy 260 Synergy 270 Synergy 280 Synergy 360 Synergy 370 Synergy LC and Synergy Solo
Compatible with Marantec belt rails: M13-1207B M13-1208B M13-1210B M13-1212B. M13-1214B

8030196

Marantec Belt Connector Kit

Works for all Marantec Belt Drive Openers
For models: Mac Lift M4500M4700Q7500Q7700 M4500e M4700e
Includes two connector pieces and four screws
Not for use on the heavy duty rails used by Q7900 & M4900e

8030279

Marantec Replacement Belt with Tab for 8ft Door

Overall Belt Length = 250"
Travel limit tab attached to belt
For Marantec opener models: M4500 M4700 Q7500 Q7700 Q7900 M4500e M4700e M4900e Synergy 260 Synergy 270 Synergy 280 Synergy 360 Synergy 370 Synergy 380 Synergy Solo
Check the Belt Connector while you are replacing the belt. If it's worn or cracked it should also be replaced

82424

Marantec Power Board for RV- 8000 & LC-1000 Models

88573

Marantec Relay Power Board for M4500 Models

Same as # 83364

106141

Marantec Shaft Adapter