Devanco Canada - Get The Right Garage Door Opener‎ and Parts

27089A

Genie Washer

Drive shaft washer for PMX500

33223A

Genie Bushing

Drive shaft bushing on PMX500 Chain Glide

E/BLOP/122

Automatic Systems Red Arm Light - 2 Sets

Increases visibility of the arm on BL229 gate operator

CB5160500-KOR

Cable 5/16" 7x19 500' Galvanized

Galvanized Cable 5/16" 7x19 500ft spool.
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life

PRO-GHB50053-PNL

Micanan 5 HP 575V 3 Ph Gearhead with Brake No Controls

Special Order only
No controls in operator- separate panel is required

126474-7K

Spring Failure Device For 1" Shaft RH & LH Assembly

Designed to reduce the risk of the door falling in the event of spring breakage
3-3/8" offset between wall and shaft (separate extension bracket available for offset of 4-3/8" up to 6")
For 1" shaft (1-1/4" shaft available for special order)
Fits 1-3/4"-6" Torsion Springs
One device per spring is required
Not for use with duplex springs

.......more details

5001-16-WHITE

Residential Side & Top Weather-Strip 16' Long - White

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

5001-12-WHITE

Residential Side & Top Weather-Strip 12' Long - White

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

K74-MODELH

LiftMaster Main Wire Harness L3

26CW94323-CUT

Truck Door Bottom Panel with Seal (13" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes only with bottom retainer and seal (installed)

.......more details

RB741

Linear / GTO 1-Button Transmitter 318 Mhz

Standard transmitter included with all GTO gate operators
Much smaller in size than previous model and improved signal range
The single button controls the gate operator and has adjustable code settings and has (new miniature) visor clip for your vehicle and now a whole for key-ring or key chain.
It is compatible with GTO and Mighty Mule gate operators
The code settings are the 9 dipswitches located inside the cover.
Measures: 2-1/2 H x 1-1/2 W x 9/16 D.

.......more details

HBSLUD

Stainless Steel Low Headroom Bottom Fixture 2-3" Door 2-3" Track Double End Stile Sold per Pair ** NLA

Manufactured with Heavy Duty 12 ga. Rust-Proof 304 Stainless Steel
Laser Cut for a Clean Finish
For Low-Headroom Track
For 2" or 3" Doors
Fits 2" or 3" Track
Double End Stile

.......more details

MK01245

Micanan Fuse 3A 250V Sold Individually

For Micanan circuit boards
Sold per fuse

MU33-2WIRE-LH-Y

Miller Edge MU33 2-Wire NM Left Hand Yellow - Sold per Foot

MU style bumpers are designed for use with aircraft hanger doors and large specialty doors.
Must specify the exact length in feet and inches when ordering.
Mounts vertically or horizontally
Sensitivity: nominal 8-13 ibf

Worksheet

38415A

Genie Chain Drive Sprocket

For Genie & Overhead Door Models
This is a 8-tooth sprocket with a hex drive bore
Genie Brand Models: Relia-G 600 Relia-G 800 1024 2024 QuietLift-600 QuiteLift-800 1042 2042 ChainLift-800 ChainLift-600
Overhead Door Brand Models With CHAIN DRIVE: Legacy 800 2026 Standard Drive 1026

PRO-GHC-10021U-L

Micanan 1 HP 230V 1P Gearhead Operator with N1 Eyes Monitored ECB Left Hand

External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation
Full function Smart 10.0 logic board and on-board receiver

.......more details

Installation manual Specification sheet

37348R

Genie Closed Confirm Remote 915 MHz GLR-BX ** NLA

Beeps and flashes green when garage door closes.
Gives warning tone and flashes red when garage door does not close properly
Compatible with Models 4064 3064 4024 and 3024 only.
Works with Genie TriloG™ IntelliG® as well as Revolution Series models PowerMax® SilentMax® and ChainMax™ garage door openers
Requires a Genie Network Adapter
Sleek and compact design

.......more details

Programming instructions Instructions de programmation

BOLT016

Manaras Hex Bolt 1/4-20 x 4

BLSI12-PM39X

Pivin Drapeau Spring Assembly for BLS12

MX00002-110V

Micanan Brake Assembly for PRO-TB/APTB with 110V Solenoid Outside - Old Style

Replaces MX00140-110V

MD-00563

Micanan Roller Chain #40 Stainless Steel 10' Pack

MI00035

Micanan VBelt 4L 27" A-27 (4L290)

Works on light duty ops. PRO-LHA/LHAB

PRO-HBH-5011U-R

Micanan 1/2HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

1/2 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

M6-18

Molded Rubber Bumper Black 18" L x 10" W 6" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
4-1/2" depth
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles. and will not warp rust rot or harden.

.......more details

BEARING012

Manaras Flange Bearing Green for 1' bore ** Repl. by BEARING047

15/32" bolt holes

MU22-4WIRE-U-Y

Miller Edge MU22 4-Wire Universal Yellow - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

MU22-2WIRE-U-GRY

Miller Edge MU22 2-Wire Universal Gray - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

GAREX-DOORFACE

Garex Special Order Door Face Only

Ordered to the customer's exact requirements

MX00034

Micanan Brake Assembly for PRO-HHD Solenoid NOT included (MX00206)

Solenoid sold separately

TRACK-GUARD-36

Track Guard 36" Tall Safety Yellow With Base Sold as a Pair *** To Extent of Inventory

Provides impact protection to vertical track
45° angle flange adds strength protects from side impact.
7-gauge steel construction powder coated safety yellow for high visibility.
1/4” foot plate drilled with slotted holes for three 1/2” anchors.
Wall flange drilled with slotted holes for four 3/8” anchors
Includes: 60-5092 (right) and 60-5093 (left) sides

.......more details

OES-5104

LiftMaster 2" x 2" PVC Channel 16ft

Connects the door to the edge kit. 16' total (sectional doors only).

MX00119

Micanan Trolley Hardware Bag Complete (MQ00012)

PIVIN-BCSI

Special Order BCSI Gate Operator ** Price by Quote Only

31375

Doorlec Coupling Sprocket 50B23

PRO-HBH10011U-L

Micanan 1 HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand

1 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

MGJ-5011U-RH

LiftMaster Medium-Duty Logic Gear-Reduced Op. 1/2 HP 115V 1Ph Right Hand

MGJ is designed for use on rolling grilles and shutters.
Maximum recommended duty cycle: 12 cycles per hour.
Heavy-duty wormgear-in-oil-bath speed reducer
3-button station for open/close/stop functionality
315 MHz radio receiver is integral to the Medium-Duty Logic board
UL325-2010 Monitored Entrapment Capability (provides primary monitored entrapment protection through monitored photo sensors: either CPS-U or CPS-UN4 or a 4-wire monitored edge using the CPS-EI interface)

.......more details

Installation manual Sell sheet

.283-334-L

Cut-to-Length Torsion Spring .283 x 3-3/4" Left Hand Wound White

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

PRO-HHD-5011E-L

Micanan 1/2HP 115V 1P Heavy-Duty Jackshaft NM ECB No Eyes Left Hand

1/2 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Non-Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included
Emergency chain hoist with electrical cut-off for manual operation

.......more details

Installation manual Specification sheet

TRACK-3"-RAW-16

Raw Vertical Track 3" 184" 13g Sold per Piece

.375-6-L

Cut-to-Length Torsion Spring .375 x 6" Left Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

27-24417

Truck Door Dual Torsion Spring Assembly 96/35 for Whiting Roll-Up Doors

Assembly includes: shaft LH & RH springs winding cones cable drums with bearings and spring spacers.
Springs are treated with rust preventative
Roadside cable drum is color coded RED
Specs: Shaft Length: 96" Spring Length: 35" Wire diameter: .187 Winding cone color: White

MP00054

Micanan Track and #410 (#48) Chain for 8' h Door *Actual length 126"*

For 1/3 & 1/2 HP Micanan trolley operators

C-24-12-2-W

Thermal Window 24" x 12" for 2" Door White

For 2" thick door

9150000630

1/4" Stops ONLY 100/pkg

Stops only - 100 per pack

MA024RDOT

LiftMaster White Aluminum Arm with Retro-Reflective DOT Tape 12 ft

For use on Mega-Arm gate operator
Red White reflective DOT stripe

Additional arm accessories

MK-00398

Micanan Capacitor 370V 20 Mf

For limited duty 220V operators

.262-334-R

Cut-to-Length Torsion Spring .262 x 3-3/4" Right Hand Wound Red/Yellow

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

.273-334-R

Cut-to-Length Torsion Spring .273 x 3-3/4" Right Hand Wound Orange/Red

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

1EBX

Explosion Proof 1-Btn Control Nema 7 & 9 Surface Mount

NEMA 7 & 9
Explosion proof enclosure
One button control
Button: 6 amp @ 125VAC
Normally open
Metal Enclosure: H=6-1/8" W=3" D=4-3/8"

.......more details

MM00013

Micanan Chain Guard (MM00431)

Fits PRO-H/HB
New part number # MM00431

CB53205000-KOR

Cable 5/32" 7x19 5000' Galvanized Supreme ** Price on request

Galvanized cable 5/32" 7x19 5000ft spool.
Cable break strength: 2800 lbs
A higher quality cable compared to the Chinese cable.
Meets endurance test requirements of over 35000 work cycles
Lubricated for flexability and longer service life

Stainless Steel Cable Specifications

9150000626

3/32" Stops ONLY 100/pkg

Stops only 100 per pack

K32-10540

LiftMaster Gear Reducer 20:1 SL595

Same as 32-10540 32-55011 32-5501-1 G3255011

28-30081

Truck Door 1" Horizontal Track 6" Radius for T-Style Std Doors 120" Roadside (LH)

Galvanized steel 14 gauge construction
For use with 1" diameter rollers
6" radius for smooth door operation
Track coupler used for proper alignment at track joints

PRO-TB-5011-U

Micanan 1/2HP 115V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

SD751L5-RH

LiftMaster Heavy-Duty Slide Door Operator 3/4HP 115V Right Hand (Must include hardware box)

Perfect for split and sliding doors involved with industrial applications.
It is installed above the door and corresponds with the direction the door will be traveling.
Comes equipped with an emergency disconnect and for manual lifting in an emergency and automatic reconnect.
The new logic 5 commercial operators come with MyQ Technology built in. * 828LM required
Built In Security+ 2.0 radio receiver
Solenoid brake included

.......more details

Installation manual Manuel d'installation Sell sheet Brochure

2376.171_22.840

Whiting Torsion assembly .171 wire size 22" spring length 84" shaft

ME00035

Micanan Limit Shaft Light Duty 3/8-1/2 x 8-1/2"

MD-00278

Micanan Roller Chain Nickel Plated #410 Sold by the Foot

41A6298

LiftMaster Hardware Installation Bag for 3800

.312-334-R

Cut-to-Length Torsion Spring .312 x 3-3/4" Right Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

38072020

Tie Down Chain Assembly GR 70 5/16" x 20' Hook / Hook

Boron manganese steel heat treated chain
Hook on both ends
WLL LBS : 4700

MT-2B

Linear 2-btn MegaCode Block Coded Transmitter 318 MHz

Compatible with all Linear access receivers and controllers
Superior transmission range
Operate LED
Visor clip included
Sold in lots of 10
Power: 9-volt battery

.......more details

SL332-ZP-COPPER

Zinc Plated Copper Sleeve 3/32" 100 Sleeves per Pkg *price on request

Oval sleeves ONLY
Stops sold separately part # ST332COP. Stops are not zinc plated

JDMG-LG-A030

GDI Jackshaft 24VDC Nema 4

Brushless DC high reliability high efficiency and low maintenance motor
No maintenance GearMotor sealed stainless steel bearings no limits switches no belts or no hydraulic cylinders to maintain
Soft start soft stop
Includes cycle counter timer-to-close 10ft motor wire harness
Battery backup optional (sold separately)

Sell sheet Technical document

D-2-6

Keyed Disconnect Device 6ft Cable

Operated from the outside to disconnect the trolley for manual operation of the door
Must specify if keyed alike is required or keyed random will be shipped
Mounting plate dimensions: 2 1/2” x 1 3/32”

ALUM-559

Aluminum 24" x 100' Spool Pebble / Kaki # 559

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 559
Reverse side is #431 Bright White

Colour chart

8X118-WHITE

Fasteners Wood Screws painted White 1000/Box

Ideal for residential weatherstrip

25050

Doorlec Explosion Proof 3-Btn Pushbutton Control Station

CSA and UL labeled station
Three button O/C/S Nema-7/9
Surface mount
Rated: Class 1 Division 1 Groups C.D.E.F.G.

GD-STEND-24D

End Cap Steel 18G 24" Double 1-3/4"

41A7920-2

LiftMaster Hardware Kit

K001C3196-3

LiftMaster Antenna 315MHz

Fits SL595

K001A5859

LiftMaster Elite Dual Motor Circuit Board Q171 ** NLA

Old style fits SL3000 CSW 200 with Q019 boards only
This board has been discontinued and no replacement available

SNACPH39

LiftMaster HID 30-bit Proximity Card Facility Code 9 *Discontinued*

Same as SN000099-30-9
Compatible with KPR2000 reader
Replaced by LMPC2-SN (need to know facility code)

BCH753L5-LH

LiftMaster Hoist Op. with Carwash Mod. 3/4 HP 208/230/460 VAC 3 Ph L5 Left Hand ***Replaced by CRBH753L5-LH

Industrial Duty Hoist Operator with Damp Environment modification
Comes with CPS-UN4 photoeyes
External brake included

Installation manual Manuel d'installation Sell sheet Brochure

BL-08

Barlock Kit Complete for 8ft Wide Door Kit includes hardware bag

Kit includes hardware bag and bars (49-1/2")

Assembly Manual

K74-34821

LiftMaster Reset Switch

Complete with reset button and mounting bracket

K75-34828

LiftMaster Idler Shaft Kit

Complete with: Bearings Sprocket 50B12x1" and Idler Shaft.
For SL575 SL585 with GL Board

SSZP15-6-114

Solid Shaft 1-1/4" Keyed 15'6" Zinc Plated

Actual length is approx. 15'-6"

SLR-221

Linear Residential Slide Gate Op. 1/2HP 230V 1 Ph - Cold Weather Package NOT Included

Integral entrapment sensing system with digital set point for quick accurate adjustment and enhanced safety
Continuous-tone entrapment alarm with reset button
LED diagnostic display for ease of setup and troubleshooting
Selectable pre-start and run alarm with provision for ADA compliant visual pre-start and run alarm
Regulated 24 Volt DC power available for access control accessories
Integrated maximum run and auto close timer (0-9 minutes)

.......more details