Devanco Canada - Get The Right Garage Door Opener‎ and Parts

3002-200FT

Gum Hose 1/2" ID 200' Spool

1/2" inside diameter
Installed in bottom "U" rubber for use as a safety edge

50-106

Take-Up Reel 2-Wire Metal 18-ga 20ft

18-gauge
20 ft extended
Take up reels are NOT recommended for use with any failsafe type edge. Use coil cord only.
Also called Reel cord

50-104-2

LiftMaster Orange Coil Cord 3-Wire 18-ga 20 ft. Extended Curly Cord

50-104-1

Black Coil Cord 2-Wire 18-ga 20 ft. Extended Curly Cord

Retracted Length=4 Feet Extended Length=20 Feet 2 Wire 18 Gauge Cord Type SJEO

50-107-30

Take-Up Reel 3-Wire Metal 30ft Extended

3- wire 18-gauge
Also called Reel Cord

655202

LiftMaster Pneumatic 14' Sensing Edge with 2-Wire Take-Up Reel

REEL-20

Devanco Take-Up Reel 2-Wire Metal 18-ga 20ft Black

18-gauge
20 ft extended
Take up reels are NOT recommended for use with any failsafe type edge. Use coil cord only.
Also called Reel cord

MWTA12

Miller Edge Transmitter with Audible Alarm Small *** No Longer Available

The MWTA12 safety edge transmitter is designed to provide wireless signal transmission form the safety edge to the motor controls.
It is easily mounted and wired to the gate or door edge sensor. When the sensing edge comes into contact with an obstruction a closed circuit signal is created and is sent to the transmitter.
The transmitter relays the information to the receiver and the receiver passes the signal along to the operator motor.
The gate or door stops movement and will then reverse the direction of travel.
Comes with an Audible Alarm feature that activates when the battery is running low and needs to be replaced.
Comes standard with a NEMA 4 weather-proof enclosure. The enclosure can be easily mounted with the four mounting holes and screws provided.

.......more details

Installation Manual Sell Sheet

50-101-2

Exterior 3-Wire Air Switch SPDT with Plastic Housing Mosley

Nema 4
3-wire air switch; 1-NO and 1-NC contact
Mosley
NO contact on Yellow and Green

MWTA12B

Miller Edge Transmitter with Low Battery Alarm Small

The transmitter comes standard with a NEMA 4 weather-proof enclosure
Compact design that allow for easy troubleshooting.
The transmitter has an audible alarm that activates when the battery has 25% of its life remaining
Easy to configure · Non-monitored system ideal for operators manufactured prior to: · Doors: August 2010 · Gates: January 2016 · NEMA 4 transmitter built to endure rugged environments
Power Source: (2) 1.5 volts AA lithium batteries
Input: 2-wire N.O. sensing edge

.......more details

3002-CUT-LENGTH

Gum Hose 1/2" ID Sold per Foot

1/2" inside diameter
Installed in bottom "U" rubber for use as a safety edge

50-105

LiftMaster Black Coil Cord 4-Wire 18-ga 20 ft. Extended Curly Cord

MWT12

Miller Edge Transmitter RF in Nema 4 Enclosure

The MWT12 safety edge transmitter is designed to provide wireless signal transmission form the safety edge to the motor controls.
It is easily mounted and wired to the gate or door edge sensor. When the sensing edge comes into contact with an obstruction a closed circuit signal is created and is sent to the transmitter.
The transmitter relays the information to the receiver and the receiver passes the signal along to the operator motor.
The gate or door stops movement and will then reverse the direction of travel.
Comes standard with a NEMA 4 weather-proof enclosure. The enclosure can be easily mounted with the four mounting holes and screws provided
Response time: nominal 30msec.

.......more details

MWRTA12

Miller Edge Wireless Transmitter with Audible Alarm and 1 Channel Receiver

For 2-wire edges
Was previously MWRTA02A now has a new board making installation easier
Includes single channel receiver (MWR12A) and transmitter (MWTA12) with audible low battery alarm.
This feature that activates when the battery has only 25% of its life remaining indicating the battery should be replaced. The alarm sounds for 5 to 10 seconds at 1 to 2 minute intervals.
The receiver operates on either 12 or 24 volt AC/DC and provides N.O. or N.C. output.

Installation Manual Sell Sheet

MWR12

Miller Edge 1-Channel Receiver RF 318 MHz

��The MWR12 receiver is designed to receive information from the transmitter and relay it to the motor to stop or reverse motion if the edge comes into contact with an obstruction.
Power requirements: 10 to 40 VDC 10-30 VAC
Output: dry relay contact N/O and N/C 1A @60VAC
Operating temperature: -40C to 60C
Maximum operating distance: 100ft
Electrical configuration: optional N/O or N/C

.......more details

Installation Manual Sell Sheet

C184-24B

Coil Cord 4 Wire 18-Gauge Black Extends 24ft

WEL-200

EMX Wireless Edge Link Transmitter / Receiver Kit

Provides a complete wireless solution for interfacing sensing edges with gate and door operators
The Wireless Edge Link eliminates the wiring between the safety edge and operator control box
No wiring needed reduces installation cost
Compatible with NC 10K and pulse monitored outputs
Operates two years on two AA lithium batteries
Connect up to 4 safety edge transmitters

.......more details

50800

LiftMaster RBMA Electric Treadle Nema 4/12 5ft long

Five feet long.
OPEN only (all LiftMaster operators) or SAFETY only (LiftMaster operators with type B2 C2 L2 T T1 or TS control wiring) after vehicle passes over treadle.
The weight of the vehicle compresses an electric switch which sends an open signal to the door.
Requires a 2-wire connection to the operator but does not require power to function

MEL-T315

Miller Edge MEL Transmitter 315 MHz 2nd Generation

MEL provides a wireless signal transmission from an edge sensor to operator controls eliminating the need to hard wire these devices

RAH-750-100

Pure Gum Rubber Air Hose 3/4" ID 1/8" Wall Beige 100ft


User Name:
Password:
Remember Me:

	Forgot your password
Request a Login