Devanco Canada - Get The Right Garage Door Opener‎ and Parts

PRO-J-10023-U-RH

Micanan 1HP 230V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft
Emergency disconnect with electrical cut-out switch for manual operation
Three button open-close-stop control station Nema-1
#41 roller chain & sprockets on all internal drives
#50 roller chain and sprockets on final drive
1" permanently lubricated & sealed ball bearings on final drive shaft
External radio control terminal strip

Pro J Manual Specification Sheet

TRACK-SET-2STD-7

2" Tracks Set 7'-0" Torsion 1-3/4" Door Clips for Wood Frame 12" Radius *** By quote only

MK-00704

Micanan Harness 1-Phase Contactor Board

MK-00053

Micanan Overload Reset 3-Phase 8.0 - 11.5 Amps

MK-00056

Micanan Transformer 230V-115V-50VA

MK-00062

Micanan Timer Base 8-pin

In closing cycle door will stop for 1.5 seconds and reverse to fully open

MV-00022

Micanan Pull Cord SPST Nema 7/9

MV-00005

Micanan PBC-3 3-btn O/C/S Nema-1 Pushbutton Control Station Flush Mount

Flush mount

PRO-H-5083U-RH

Micanan 1/2HP 208V 3P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

1005-1-3/8-12'

Aluminum Bottom Retainer U-Shaped 12' Long

For door thickness 1-3/8"

OSH-6434-ECB-LH

Manaras Opera-SH 1 HP 480V 3 Ph with Electronic Circuit Board Left Hand

An ultra high-end heavy-duty V-belt drive industrial jackshaft operator
For use on Standard High and Vertical Lift sectional doors
Can also be used on Rolling doors and Grilles
Comes with a chain hoist for manual operation and a floor level engaging device
Clearence: side room required 16"
25 cycles per day > 100 cycles per day

.......more details

Installation Manual

PRO-J-10021-U-RH

Micanan 1HP 230V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-10081-U-RH

Micanan 1HP 208V 1P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

.421-334-L

Cut-to-Length Torsion Spring .421 x 3-3/4" Left Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-375-INSTALLED

.343-258-L

Cut-to-Length Torsion Spring .343 x 2-5/8" Left Hand Wound Blue/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.295-514-R

Cut-to-Length Torsion Spring .295 x 5-1/4" Right Hand Wound Blue

Priced per inch
For factory installed cones priced seperately - use part no. C-514-INSTALLED

PRO-J-7523-U-RH

Micanan 3/4HP 230V 3P Jackshaft Monitored ECB N1 Eyes Right Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Pro J Manual Specification Sheet

PRO-J-7521-U-LH

Micanan 3/4HP 230V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-LJ-5021-U-RH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Right Hand

On-Board receiver holds up to 20 transmitters

PRO-LJ-5011-U-LH

Micanan 1/2HP 115V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

PRO-GT-10023-U

Micanan 1HP 230V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-7581-U

Micanan 3/4HP 208V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-5053-U

Micanan 1/2HP 575V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-5023-U

Micanan 1/2HP 230V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

ALUM-568

Aluminum 24" x 100' Spool Nutmeg / Brun Muscade # 568

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 565
Reverse side is #431 Bright White

Colour chart

PRO-TB-10043-U

Micanan 1 HP 460V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-T-5083-U

Micanan 1/2HP 208V 3P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

MB-05504

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 56C

Fits GT GH GHC & GSD

60-7244

Econo Caution Sign French 14" x 10"

811-11

Wheel Chock 811-11 Orange Urethane

Not For Use on Ice
High Visibility
Orange Urethane
Size: 11" wide x 8" long x 8" high

60-7248-SC8

Wheel Chock Safety Pkg incl'd: alum. chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) SC-8 Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
"Claw" Like Bottom Assures Dependable Grip on Any Surface
Chock Fits Snug Under Tire Contour for Maximum Holding Power
Often Preferred For Snow and Ice Conditions
Light Weight and Reliable
Size: 7" wide x 11-1/2" long x 8" high

.......more details

CP-SH-58-1212

Lynx Clutch Shaft Only for MCJH 5/8" x 12-1/2"

No pulley

PRO-APTB-5021-U

Micanan 1/2HP 230V 1P Apartment Trolley Operator N1 Eyes Monitored ECB with Brake

Designed for use on Commercial / Industrial high cycle sectional overhead doors with standard lift tracks.
Low clearance design for apartment applications (9.5")
External radio control terminal strip
3-btn O/C/S control station Nema-1
Solenoid brake installed
Door speed 12" per second

.......more details

MF00006

Micanan Hex Head Bolt 1/4" - 20UNC 1/2" Full Thread

Used on various Micanan operators
2 required per operator

RATCHET_BAR

Ratchet Bar for Holdown Assembly 8-8786 ** Quote Only

E/1929/070

Automatic Systems Spare Arm 14'-9" (BL229)

Used on the BL229 gate op.

ME00071

Micanan Idler Shaft PRO-APTC

LVB924-11

Laminated Bumper Black 9" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB910-24

Laminated Bumper Standard Black 10" x 24" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB406-36SF

Steel Faced Laminated Bumper Black 6" x 36" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

Q080

LiftMaster Dolly Latch Kit K75-50138

For Liftmaster trolley operator HCT

LB410-36SF

Steel Faced Laminated Bumper Black 10" x 36" 4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB610-14SF

Steel Faced Laminated Bumper Black 10" x 14" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LLB620-22SF

Steel Faced Laminated Bumper Black 6" Projection L-Shaped 20" x 22" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.

.......more details

LB612-36SF

Steel Faced Laminated Bumper Black 12" x 36" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-18SF

Steel Faced Laminated Bumper Black 12" x 18" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB436-11

Laminated Bumper Black 4" Projection Vertical Installation 36" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB412-24

Laminated Bumper Standard Black 12" x 24" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

MK-00805

Micanan Heater Probe in Reducer 24V 20W Brass Fitting Field Install

65_52091-12

LiftMaster Manual Hoist Mod. M8 #41 Chain for 12ft High Door

For 3/4 Hp & 1 Hp Trolley operators
Includes floor level brake release cable 1" x 12' round bar.

MD-00246

Double Sprocket 41B14 / 41A32 with 1" Bushing

Double sprocket for PRO-H/HB

MK-00050

Micanan Overload Reset 3-Phase 2.6 - 3.7 Amps

BTM-BK-PCG/PR

Powdercoated Commercial 3" LHR Bottom Brackets Grey Sold as a Pair (L & R) *** NLA

EZ123 UPWARDOR
Powdercoated grey
Use with: 3" straight track
Sold as a pair (includes one left and one right).

HINGE-811-PCG

Powdercoated Hinge #8 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #8 - 0.87 lbs
Powdercoated Grey
For use with 7/16" stem rollers

HINGE-711-PCG

Powdercoated Hinge #7 x 11 gauge Grey ** To Extent of Inventory

Heavy Duty 11 gauge offset hinge #7 - 0.87 lbs
Powdercoated Grey
For use with 7/16" stem rollers

9-22-1

Offset Strut Plate

WHITING-SPEC-ORD

Whiting Special Order Parts

Special order to customer's specs

MH00006

Micanan Shaft Collar 3/8" I.D

H503L5-LH

LiftMaster Ind. Duty Hoist Op. 1/2 HP 208/230-460V VAC 3 Ph Logic 5 Left Hand

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

BRACKET111

Manaras Hood Mount Angle Bracket

MP-00002-230V

Micanan Apartment Feature: Timer-to-Close Function and Light Control Modification only

Controlling action of two lights- sockets supplied on cover

MM00024

Micanan Cam Plate for PRO-HHD

26CW94323-CUT

Truck Door Bottom Panel with Seal (13" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes only with bottom retainer and seal (installed)

.......more details

PRO-H-7553U-LH

Micanan 3/4HP 575V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

82424

Marantec Power Board for RV- 8000 & LC-1000 Models

PRO-PL-15053-R

Micanan Wall Mounted Control Panel Mod (R) Contactor

Standard features include N-4/12 - 20" x 16" x 8" panel B-2 C-2 wiring 24V controls hinged cover backplate and primary fuses in panel

7001-10-BRONZE

Commercial Side & Top Weather-Strip 10' Long - Bronze (BZ)

Bronze galvanized steel with bronze dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (20)

MI00035

Micanan VBelt 4L 27" A-27 (4L290)

Works on light duty ops. PRO-LHA/LHAB

2376.206.30.930

Whiting Torsion assembly .206 wire size 30" spring length 93" shaft

26CW94322-CUT

Truck Door Bottom Panel with Seal (12" x Cut-To-Size) Painted White for Whiting Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes only with bottom retainer and seal (installed)

.......more details

SPECIAL-ORDER-SS

Special Order for Stainless Steel Door Products

MD-00189

Micanan Roller Chain Waterproof #41 Sold by the Foot

ALUM-502

Aluminum 24" x 100' Spool Maize / Ivoire # 502

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 502
Reverse side is #431 Bright White

Colour chart

AW12K500-18

Miller Edge Air Wave Kit 18ft No Coil Cord

Kit Includes: AW12 Air Wave Switch Barbed Coupler (18') RAH-500 1/2" dia. Rubber Hose Wire Nuts End Plugs

MX00119

Micanan Trolley Hardware Bag Complete (MQ00012)

029-98100

T-Style Replacement Door White Stainless Steel Package 029-98100

Replacement door size between 98" wide x 100" high
Painted white
Stainless steel package
Includes Hinges Rollers and Cable

TA-2-S/L-1200

Assembled Track Set 2" Comm 14g Bracket Mount for 1-3/4" Door Std Lift 12" Radius

Includes horizontal and vertical tracks

MG00014

Micanan Slotted Hex Nut 3/4"-24UNF

PRO-H/HB operator parts

.375-6-R

Cut-to-Length Torsion Spring .375 x 6" Right Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-600-INSTALLED

PRO-GH-7511U-R

Micanan 3/4HP 115V 1P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

9150000630

1/4" Stops ONLY 100/pkg

Stops only - 100 per pack

PRO-H-5011U-LH

Micanan 1/2HP 115V 1P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

Installation manual Specification sheet

MK-00430

Micanan Capacitor 240V/250V 70 Mf

For limited duty 110V operators

MT22-MON-Y-LH

Miller Edge 4-Wire Monitored Pressure Sensitive Edge Yellow Sold per Foot

��Electromechanical small profile edge for rolling steel foor applicaton. •Touch sensitive signaling allows for immediate stopping or reversing of motion. •The MT22 is completely flexible and will contour to curved surfaces. The MT22 also acts as weatherstrip. •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

PRO-H-7511U-LH

Micanan 3/4HP 115V 1P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

Installation manual Specification sheet

MI00001

Micanan Motor Pulley 5L 5/8" ID x 2" OD

GT751L5

LiftMaster Heavy Industrial-Duty Trolley Op. 3/4 HP 115V

Suspended from the ceiling the operators are used on sectional overhead doors with a standard lift.
GT operators are directly attached to drive and control the door
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Requires 828LM MyQ Internet Gateway to connect to MyQ Smartphone App.
High-starting torque continuous duty motor with overload protection
Door speed approx. 11-12 inches per second

.......more details

Installation manual Manuel d'installation Sell sheet Brochure

225-120R

Electraray Rotating Warning Light Red 120V

Incandescent warning light
90 flashes per minute
Operating temp. 31 to 150 degrees fahrenheit
Height: 7-1/4" Diameter: 5-1/2"
Enclosure rating: Nema4X

1104-9FT-GREEN

Residential Side & Top PVC Weather-Strip with cap 9' Long - Green (R)

Green rigid vinyl retainer with green flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

MD-00278

Micanan Roller Chain Nickel Plated #410 Sold by the Foot

FRONTIDLER007

Manaras Front Idler Assembly #48 (#410)

D-2-6

Keyed Disconnect Device 6ft Cable

Operated from the outside to disconnect the trolley for manual operation of the door
Must specify if keyed alike is required or keyed random will be shipped
Mounting plate dimensions: 2 1/2” x 1 3/32”