Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MP-00072

Micanan Jackshaft with Auxiliary Trolley Assembly 14' High Door #41 Drive Chain

Provides an auxiliary trolley assembly where otherwise a jackshaft operator may be preferred
Operator must be supplied with reversed limits
For models: PRO-J H HHD GH GHC

88573

Marantec Relay Power Board for M4500 Models

Same as # 83364

SSSS-1-6FT

Solid Shaft 1" Keyed Stainless Steel 6 ft

303 series Stainless Steel

IRB-TX

EMX Industries Transmitter Board Only for IRB-4X *** No Longer Available

PPLK1

LiftMaster Passport Lite 1-Button Mini Remote with Sec+ 2.0 Technology

Passport Lite Remote Controls provide cost-effective single button access solutions for gate access only or high-capacity commercial properties applications such as employee parking lots and tenant garages.
These remote controls are specifically designed for gate access control and are not compatible with LiftMaster Garage Door Openers.
2x the range of standard remote controls
Narrow-band transmission on 3 simultaneous frequencies (310 MHz 315 MHz 390 MHz)
Compatible with LiftMaster® commercial receivers (850LM 860LM PPWR STAR1000) and Security+ 2.0™ Gate Operators

SG-13-NO

Telco Light Curtain with Rectifier Normally Open 72" (13-193-028-D1-E-H58-5) ***No Longer Available

Normally Open
SGR13-193-028-D1-E-HS8-5
SGT13-193-028-D1-E-01-15
1928mm housing 1800mm active height 28 channels NO relay output 15m cable

Specification sheet Wiring diagram

MAG-3

Magnetic Accessories Kit 3-Piece Combo

The MagTool clipboard tape gun and box all come with an integral 100lb. magnet which allows them to be easily stuck and removed from a metal surface.

PRO-H-7581-U-LH

Micanan 3/4HP 208V 1P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

MK-00160

Micanan 12-Pole Terminal Strip

MK-00300

Micanan Time Delay on Reverse 0.5 sec. 24/110V

In closing cycle door will stop for 0.5 seconds and reverse to fully open

12119

Doorlec Commercial Aluminum Sliding Carriage with Teflon Insert

Works on all Doorlec trolley operators

.295-6-L

Cut-to-Length Torsion Spring .295 x 6" Left Hand Wound Blue

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

.375-334-R

Cut-to-Length Torsion Spring .375 x3-3/4" Right Hand Wound Yellow/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-375-INSTALLED

.319-258-L

Cut-to-Length Torsion Spring .319 x 2-5/8" Left Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-258-Installed

K001A6426-2

LiftMaster Control Board RSL12V/RSW12V

CAPXL

LiftMaster Connected Access Portal High Capacity

Connected Access Portal High Capacity Cloud-based access control for residential communities.
Capacities: 4 Controlled Gates/Doors
Wireless Link for up to 8 LiftMaster® Operators
4 to 8 Digit Entry Codes
4 to 6 Digit Directory Codes
50000 Local Resident Capacity

.......more details

LB812-14

Laminated Bumper Standard Black 12" x 14" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB636-11

Laminated Bumper Black 6" Projection Vertical Installation 36" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

108135.0003

Overhead Serpentine V- Belt for JST 26"

Overhead Door commercial garage door opener serpentine belt 108135-0003 included in the "speed-up" kit for sidemount only
Type "J" 26"

CABLE_364SS-250

Cable 3/64" 7x7 250' Stainless Steel

Not for use in aircraft applications
Type: T304

H503L5-RH

LiftMaster Ind. Duty Hoist Op. 1/2 HP 208/230-460V VAC 3 Ph Logic 5 Right Hand

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

ALUM-569

Aluminum 24" x 100' Spool Saddle Brown / Brun Fauve # 569

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 569
Reverse side is #431 Bright White

Colour chart

4007-7FT

Aluminum Retainer only for Light Brush 90 degree

For angle application
For use with Light Brush or Vinyl Insert.

DS350

Heavy-Duty Commercial Non-Insulated Rollup Sheet Door with Interior Slide Locks

Heavy-duty Model DS-350 has statewide Florida product approval for wind load protection up to 190 mph.
This door is ideal for commercial applications with openings up to 16’ wide by 16’ high.
Heavy-duty 13-gauge guides attach to 8-gauge wall angles to give maximum wind load protection.
Installation to masonry or steel is quick and simple with no special preparation or overhead tracks needed.
A wide selection of colors to choose from
Made to Order

.......more details

MV-00300

Micanan Banner Intrinsically Safe Reflective Photocell ONLY (0-25ft. Range) *** Special Order POR

Model Q45AD9LV same as part # 37620
Range: 9 m; Input: 5-15V dc
Output: NAMUR
2 m (6.5 ft) cable
Nema rating: NEMA 6P
DOES NOT include the bracket or the reflector. Use MV00482 for the kit

.......more details

7001-18-BRONZE

Commercial Side & Top Weather-Strip 18' Long - Bronze (BZ)

Bronze galvanized steel with bronze dual fin vinyl.
Commercial and Residential use.
Steel is notched on both ends for easier installation.
Full case quantity only (10)

M6-18

Molded Rubber Bumper Black 18" L x 10" W 6" Projection 2-Hole Sold Individually

Manufactured from reinforced prime rubber
Rectangular horizontal mount
4-1/2" depth
Ideal for light traffic loading docks.
Molded bumpers are molded in one piece and will not warp rust rot or harden.
Perfect protection for in-plant wall protection from forklifts and other material handling vehicles. and will not warp rust rot or harden.

.......more details

PRO-HB-5053U-RH

Micanan 1/2HP 575V 3P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

PRO-HBH10011U-L

Micanan 1 HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand

1 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

MGJ-5011U-LH

LiftMaster Medium-Duty Logic Gear-Reduced Op. 1/2 HP 115V 1Ph Left Hand

MGJ is designed for use on rolling grilles and shutters.
Maximum recommended duty cycle: 12 cycles per hour.
Heavy-duty wormgear-in-oil-bath speed reducer
3-button station for open/close/stop functionality
315 MHz radio receiver is integral to the Medium-Duty Logic board
UL325-2010 Monitored Entrapment Capability (provides primary monitored entrapment protection through monitored photo sensors: either CPS-U or CPS-UN4 or a 4-wire monitored edge using the CPS-EI interface)

.......more details

Installation manual Sell sheet

109435.0001

Overhead Limit Switch

27028

Doorlec Electric Motor 3/4HP 115/230V DC403C

Bolts to gearhead (c-flange) openers

Wiring diagram for 120V Wiring diagram for 230V

22-00627

Truck Door Grab Handle 13" Chrome Steel

Steel construction Chrome finish
Cross ref: Eberhard 4300

785105

FAAC XP30 Photocells 30m Range Relay

Hardwired pair of Photocell relays
30m Range
IP54
24v
Dimensions: 55 L x 78 H x21 D mm

PRO-H-5011R-RH

Micanan 1/2HP 115V 1P Hoist Operator Contactor Model Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Solenoid brake OPTIONAL

Installation manual Specification sheet

S142ARNN115

Carlo Gavazzi Amplifier 115V

Processor controlled amplifier for one set of photoelectric sensors type MOFTR.
11-pin circular plug for easy connection.
8A SPDT relay output NPN/ PNP transistor output or alarm output.
Diagnostics for sensor test during operation.
Alignment help via LED or alternation of alarm output.
Level indication for dirt accumulation.

.......more details

LMTBU

LiftMaster Monitored Through Beam Photo Eye Nema 4X ** To exent of inventory

Meets 2016 UL 325 requirements
Long Range powerful beam provides reliable performance.
Sensing distance up to 90 ft.
Anti-Fogging Lens
NEMA 4X rated
Wireless network mode eliminates the need to wire between operators in dual-gate applications.

.......more details

1005-2-14

Aluminum Bottom Retainer U-Shaped 14' Long**Actual Length 14'2"***

For door thickness 2"

E3JM-30FT

Omron Thru-Beam Photoelectric Sensor Nema 4 0-30ft Range

Easy-to-wire terminal block
Built-in timer offers selectable ON-delay OFF-delay and one-shot
Relay or transistor output models
Light-ON/Dark-ON operation switch selectable
Model: E3JM-10M4-US

41A3589-1

LiftMaster 8ft Belt Assembly for Models '93-2000

For use with LiftMaster belt drive models 1270 1280 1280R.
Full belt assembly
For use with Chamberlain belt drive models 8100 8200 and 9200.
For standard 8 foot high garage doors
T rail assemblies ONLY.

7812

Whiting Bottom Seal Truss Door White 90" Long

Fits Fed-Ex truck doors

1104-9FT-GREEN

Residential Side & Top PVC Weather-Strip with cap 9' Long - Green (R)

Green rigid vinyl retainer with green flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

FRONTIDLER007

Manaras Front Idler Assembly #48 (#410)

108D36

LiftMaster Light Lens (K108D0036-2)

Compatible with one light operators
Compatible with the following Liftmaster models: 1040 1045 1055 100WD 200WD 1140 1145 1155 110WD 210WD3 1240 1245 1255 215WD 15WD 1240R 1245R 1255R 985 1046 1146 1246 1246R 1056 1156 1256 and 1256R
Compatible with the following Chamberlain models: 2000 2100 and 2200
Dimensions are 7-1/4" wide X 4-3/4" high X 3" deep

.218-325-DS75

Mini Storage Spring for DS75 4x7 Door

Spring only with loop ends

8360WLB

LiftMaster 3/4 HP DC Premium Series Chain Drive Wi-Fi Lock with BBU Capability **To extend of inventory

Built-In Wi-Fi® for the easiest way to connect the garage.
Real-Time Alerts indicate the status of the garage door via email or push notifications.
Monitor and Control the opener from anywhere using mobile devices.
Consume up to 75% less power in standby mode.
Soft Start/Stop for smooth operation.
Safeguard your household with Security+ 2.0™-with every click a new code is sent to the Garage Door Opener so the door opens only for you.

.......more details

ULTRA-II-D-TEK

EMX Industries Plug-in Loop Detector (2663-1)

Features a slim design that is compatible with most gate operators that require a dry contact relay input.
No harness required; comes with terminal screw adaptor
ULTRAMETER™ (displays optimum sensitivity setting / diagnostic aid)
Frequency count/reset switch
10 sensitivity settings
Loop diagnostics

.......more details

0-7530-444

FHP Electric Motor 1/3 HP 110V 1625 RPM Motor A099231

60-2439

Allen Bradley Swivel / Tilt Mounting Bracket ***To Extent of Inventory

For 9000 series photo switches

MK-00697

Micanan Fraba FOS-1 Exterior Thru-Beam Photocell Nema 4 / 4X 45ft Range

Exterior Through-Beam Photocell
Sensing Distance 45 Feet
UL325/2010 Recognized Component
Comes with Sender Receiver and Brackets
NEMA 4 & 4X

Installation manual

HTRNB

LiftMaster Heater Kit for AC Pad Mount Gate Operators

Heater kit for pad mount AC gate operators.
Battery bracket NOT included.
Protects system to -40° F and installs on operator frame
Measurements: 6 x 2 3/8 x 3 3/8

LVB620-11

Laminated Bumper Black 6" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

ALUM-525

Aluminum 24" x 100' Spool Black / Noir # 525

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 525
Reverse side is #431 Bright White

Colour chart

BK200

Flat End Plate with Bearing 5-5/8" 4-Hole Sold per Piece

8-gauge
Includes commercial-grade semi-precision ball bearing bearing
3" wide

WASHER008

Manaras Type A Plain Washer 5/16" Zinc Plated

Used on old MJH

BOLT027

Manaras Hex Bolt 3/8-16 x 1-1/2"

Used on old MJH

CSL24UL

LiftMaster New 24VDC Commercial High Traffic DC Slide Gate Operator

Battery Backup: 208 cycles or up to 24 days of standby power when the power is down
Security+2.0®: Access your property quickly with Security+2.0® Technology that utilizes a tri-band signal that virtually eliminates interference and offers extended range each time the remote control is used
MyQ®: Securely control and monitor your Gate Operator from anywhere and get activity notifications through the MyQ® app
Soft start / stop extends operator and hardware life in high-cycle and heavy-gate applications
Wireless dual-gate communication eliminates expensive conduit costs and unsightly driveway scars
Keyed manual disconnect when unlocked allows gate to be operated manually.

.......more details

Installation manual Manuel d'installation Sell sheet

JRGX114

Chain Hoist Jack Shaft JRG V2 1-1/4" Shaft Torque Force (126690)

Jack Shaft Mounting plastic guide 4.5:1 reduction
Gear drive
Fits 3-3/8" minimum offset
Includes: 26' of galvanized hand chain - doors higher than 15' require additional hand chain
1 chain keeper
2 shaft collars

.......more details

Sell sheet

MHS5011U-RH

LiftMaster 1/2 HP 120 Volt Medium Duty Slow-Speed Jackshaft Operator

Designed for use on rolling sheet doors.
It features an adjustable friction clutch high-starting torque motor with overload protection emergency chain hoist with electric interlock and emergency disconnect chain.
Easy emergency manual operation using a floor level disconnect and an electrically interlocked chain hoist mechanism
Floor level disconnect
24V NEC Class 2
Wiring is factory present to C2 mode

.......more details

Installation manual Sell sheet

MD00044

Micanan Spur Gear 12B60

101475

Insert Bearing 1-1/4" Bore SB206-20

Works with Flangette Retainer 102079

K72-33192

LiftMaster Limit Shaft Kit NEMA 4 & 4X for H J HJ GH GT T & APT Operators

For: NEMA 4 & 4X for H J HJ GH GT T & APT Operators
Shaft measures 12" in length
Compatible with Logic 4 and Logic 5 operators

25-60503

Truck Door T-Style Ramp Handles Curbside (Right)

Black plastic construction
Cross ref.: 39504-2

MALED17

LiftMaster LED Barrier Arm 17 ft

The NEW LED Barrier Arm provides exceptional visibility 24 hours a day.
Durable aluminum arm with integrated red LED lights on one side and Red/White DOT tape on both sides.
Ideal for use with the Mega Arm and Mega Arm Tower
Counterweight required part # MALEDCW

CABLE-NR-14-CC

Cable No Roll 1/4" 19x7 Non-Galvanized C-Coated 500ft

19X7 rotation-resistant wire rope.

CP-SH-58-1038

Lynx Complete Limit Shaft Assembly for MCJH

5/8" x 10-3/8"
Same kit used for HDC except the HDC has 1 extra 5/8" space washer

N7/9-MOD

Micanan Explosion Proof Modification

Modification available on certains models only

BG790-50-11

LiftMaster Industrial-Duty Wishbone Barrier Gate Operator 1/2 HP 115V Arm & Weight Included ***Must include Arm G651208R***

A reliable gear-driven barrier gate operator that is perfect for industrial applications.
This barrier gate is designed for Wishbone-Type Arms with lengths of up to 24 ft.
The BG 790's powdercoated weather-resistant steel enclosure and its 1/2 HP commercial motor ensure strong dependable performance.
Standard Features: Control inputs and Adjustable limit settings
Includes a 24' arm

Installation Manual Sell Sheet

MD-00030

Roller Chain #40 10' per Pack

Includes (1x) master link

HSCC112

Hinge Combination Hinge Clopay Style 12-ga Stainless Steel

Manufactured with Heavy Duty 12ga. Rust-Resistant 304 Stainless Steel
Laser Cut for a Clean Finish

41D605-1

LiftMaster Electric Motor 80kg/100kg

For retail models: WD952KD HD800D and WD952LD

Replacement Instructions Instructions de remplacement

MK00737

Micanan Feature Circuit Board with Contactor Interface Non-Monitored 575V **use MK00642-NM

For all HP - 575V all voltages 1.5 2 3 & 5HP
Non-Monitored

Instructions Manual

MK00642

Micanan Smart 10.0 Full Feature Circuit Board with Contactor Interface Monitored 575V

For all HP - 575V all voltages 1.5 2 3 & 5HP

Instructions Manual

MT-UHF-0-0

AWID Long Range Metal Mount Tag

For use with LR-2000 and LR-3000 readers
Operating temperatures from -58°F to 185°F (-50°C to +85°C)
Reading Distance up to 25 feet
Battery not needed passive tag
Passive RFID technology with excellent-price-to-performance ratio
Proprietary encryption for protection of card data

.......more details

FGS-634

Devanco Food Grade Silicone 262g

For use in food and industrial plants
Stops squeaks
Prevents sticking and corrosion
Protects rubber mouldings and weather stripping

Safety Data Sheet Fiche de données de sécurité

29-98200

W-Style Universal Drop In Door 98" x 100"

Shipped with hardware loose on each side
98" W x 100" H
Made with 3/4" thick 7 ply exterior grade medium density plywood
Includes all hardware
Other sizes available

USVD-4X

EMX Ultra Sonic Vehicle Detector 2700-1

The USVD-4X Drive Thru Vehicle Sensor uses patent pending Triangular Planar Array (TPA) technology to detect the presence of a vehicle.
The USVD handles any drive thru operation such as fast food banking pharmacies car washes and parking garages.
The USVD is simply mounted on a post or order box and aimed at the location where a vehicle would pass to initiate a transaction. No set-up or adjustments required.
Aux. relay settings for pulse on ENTRY EXIT or BOTH
Output delay option for 1 2 and 4 seconds
Operating range: 1ft. – 5ft.

.......more details

Installation Manual Sell Sheet

PRO-HBH-7511U-L

Micanan 3/4HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand (Pro-HHD)

3/4 HP115V 1PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

EAST/STL-E3

Rolling Steel 3" Cast Eastern Steel Endlock

Endlocks are riveted to curtain slats ends of every other slat to prevent slats from shifting laterally and to prevent curtain wear in guides.
Continuous endlocks are both ends of every slat.
Rivets included with endlocks

SLT17-20

Rolling Steel 2" Flat Slat 20-ga Galvanized

CH753L5-RH

LiftMaster Hoist Op. with Carwash Mod. 3/4 HP 208/230/460 VAC 3 Ph L5 Right Hand

Industrial Duty Hoist Operator with Damp Environment modification
Brake not included
Comes with CPS-UN4 photoeyes

Installation Manual Manuel d'Installation Sell sheet Brochure

.319-334-L

Cut-to-Length Torsion Spring .319 x 3-3/4" Left Hand Wound Blue/Green

Priced per inch. Cones sold separatly.
For factory installed cones order part # C-334-Installed

41C5141-2

LiftMaster Trolley Assembly Belt Drive

For retail model
For belt drive

SHAFT017

Manaras Spacer for Trolley Tracks

AK-21

Linear Interior Digital Keypad ***to extent of inventory

The keypad is housed in a rugged plastic enclosure and is designed to be mounted in a standard single-gang electrical box. The die-cast keys have bright easy-to-read yellow graphics.
It is supplied with four different plastic snap-on mounting bezels to customize the look of the keypad. The satin-chrome bezel comes factory installed on the keypad. The white ivory & bronze bezels are packaged separately.
Up to 480 entry codes from 1 to 6 digits in length can be programmed. They can activate either or both of the relay outputs.
Relay #1 has a 5 Amp capacity. Relay #2 has a 1 Amp capacity. The relays can be set for timed or latch-on/latch-off toggle operation per each individual entry code.
The on or off toggle state of a relay is maintained even after power interruption. When power is restored to the keypad each relay will assume the state it was in when power was removed.

Installation Manual

36254R

Genie T-Rail Carriage Assembly

This part is listed under several part numbers: 36254R.S 36197A 21784R 20438R
For all chain drive openers with steel T-rail assemblies
Must be installed with inner slide part # 25605R

33950R

Genie Up Limit Switch Assembly 66 " Wire

For use on 7'6" rail assemblies.
For Genie Excelerator models and Overhead Overdrive models
Open / Up magnetic limit switch

K204C0211

LiftMaster Torroid Transformer

Transformer replacement kit for use with various LiftMaster® Commercial Slide and Swing Gate Operators

CPE

Erone Proximity Card Standard *** To Extent of Inventory

Hexadecimal number printed on each badge
8mm thick

37028C.S

Genie Control Board for Model 2022 ** Repl. by 39537R.S (no cover)

For ReliaG 800 model 2022 gaarage door opener ◾ Genie 37028A Control Board for Genie Models 2022 2024 and 2042 Chain / Belt Drive Openers ◾ Works for the following models only: ◾ ReliaG 800 (2024) PRO Series 1 Piece Rail ◾ QuietLift 800 (2042) ◾ ChainLift 800 (2022)

SSZP8-6

Solid Shaft 1" Keyed Zinc Plated 8'-6" (102")

CH505L5-LH

LiftMaster Hoist Op. with Carwash Mod. 1/2 HP 575 VAC 3 Ph Logic 5 Left Hand

Industrial Duty Hoist Operator with Damp Environment modification.
Comes with CPS-UN4 photoeyes
Comes with 02-403P NEMA 4 push button

Installation Manual Manuel d'Installation Sell sheet Brochure

RS1039-C

Roller 3" Steel 9" stem 10 ball Torque Force

Steel Roller Wheel diameter: 3"
Working length: 8.5"
Overall length: 9.64"
Box qty: 75

K21-36793

LiftMaster Transformer 208-230/460 Volts 20Va

230/460V PRIMARY 24V SECONDARY 20VA

41DB001-1

LiftMaster Circuit Board Assembly

For belt drive unit model 3500 (315MHz)
Assembly includes: Board end panel and light socket
Also known as 041DB001-1C

75-10170

LiftMaster Trolley-Slider Assembly (08-10169)

For LiftMaster trolley models MT T GT
Also known as: 307085008 75-10170 08-10169 085008 7510170

MOFR-M14-8

Carlo Gavazzi Photoelectric Sensor Thru-Beam Receiver

Maximum sensing range is 20 meters
11-Pin
8 inch optical beam angle.
Waterproof for harsh environments i.e. water dust steam etc.
To be used with amplifier series S142
Supplied with 15 m of shielded cable.

.......more details

Installation Manual

27-20112

Truck Door W-Style Spring Assembly Curbside 33" Long

Wire thickness: .182
Spring length: 33 inches long (assembled length)
Inside diameter: 1.188
Includes cable drum and bearing assembly winding cone wound onto spring for stronger desgn and internal spring spacer.