Devanco Canada - Get The Right Garage Door Opener‎ and Parts

STATION080

Manaras 3-btn Push-Button Control Station with Key Lock-Out and Pilot Light Nema 4/12

2 N/O contacts and 1 N/C contact for stop.
Surface mount.
Schneider Elect. part no. XALD04H7

LB812-24

Laminated Bumper Standard Black 12" x 24" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB810-24

Laminated Bumper Standard Black 10" x 24" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB420-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 20" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

Drawing

TB412-14SF

Steel Faced Laminated Bumper Black 12" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-14SF

Steel Faced Laminated Bumper Black 10" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB610-18SF

Steel Faced Laminated Bumper Black 10" x 18" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LLB620-22

Laminated Bumper Black 6" Projection L-Shaped 20" x 22" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.
This model has angles on both sides

.......more details

LVB636-11

Laminated Bumper Black 6" Projection Vertical Installation 36" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB412-18

Laminated Bumper Standard Black 12" x 18" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB410-24

Laminated Bumper Standard Black 10" x 24" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB410-36

Laminated Bumper Standard Black 10" x 36" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

MK-00120

Micanan Heater Probe in Reducer Mod. (120V 20W 3/8" NPT)

65_52091-12

LiftMaster Manual Hoist Mod. M8 #41 Chain for 12ft High Door

For 3/4 Hp & 1 Hp Trolley operators
Includes floor level brake release cable 1" x 12' round bar.

Z9211-1

Stationary Cone Tool 1-3/4" & 2"

Easily dislodges the cone from the torsion spring

MM00149

Micanan GHC Frame Support U-Bracket MSI0161 (for 2 3HP)

MF00002

Micanan Hex Head Bolt 1/2" - 13 UNC x 1-1/4"

Used on PRO-GHC
4 required per operator

MG00041

Micanan Spring Clip 7/8" ID Sold Individually

2 required per machine

RCB-TIP

Roller Chain Break Replacement Tip Only *** NLA

Replacement tip only for RCB-2560

TRACK-SET-2

2" Tracks Set with Wall Brackets Special Order

Custom order to customer's needs
Set includes the vertical and horizontal tracks and wall clips for either wood or steel.
Must spcify if the door has torsion or extension springs if the tracks are going on a wood jam or steel desired radius and thickness of door

VWS-34-CHRY-OAK

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Cherry Oak

Pan head

MD-00280

Sprocket 41B32 x 1" 1/4" Keyway 2SS 5/16 Small Hub

2 set screw 5/16

MB-15204

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 145TC

Fits GT GH GHC & GSD

6X35PO50

Devanco Loop 6' x 35' pave-over 50' lead-in

Ideal for use on with gravel driveways or sufaces that are to be asphalted
Features a twisted lead-in to reduce the chances of interference and false detections.
Direct burial loops should be buried approximately 6" deep

38415A

Genie Chain Drive Sprocket

For Genie & Overhead Door Models
This is a 8-tooth sprocket with a hex drive bore
Genie Brand Models: Relia-G 600 Relia-G 800 1024 2024 QuietLift-600 QuiteLift-800 1042 2042 ChainLift-800 ChainLift-600
Overhead Door Brand Models With CHAIN DRIVE: Legacy 800 2026 Standard Drive 1026

PRO-GHC-10021U-L

Micanan 1 HP 230V 1P Gearhead Operator with N1 Eyes Monitored ECB Left Hand

External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation
Full function Smart 10.0 logic board and on-board receiver

.......more details

Installation manual Specification sheet

MD-00516

Micanan Roller Chain #40 Waterproof 10' Pack

26CW94222-CUT

Truck Door Bottom Panel with Hardware (12" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes with pull strap two bottom roller shaft covers stud plates standard lift handle seal & retainer

.......more details

33101

Overload 0.90 to 1.50A

Setting range 1.1 - 1.6A

MX00034

Micanan Brake Assembly for PRO-HHD Solenoid NOT included

Solenoid sold separately

5001-12-DK-BROWN

Residential Side & Top Weather-Strip 12' Long Commercial Brown

Painted aluminum retainer with flexible dual fin vinyl.
Residential use.

OES-5104

LiftMaster 2" x 2" PVC Channel 16ft

Connects the door to the edge kit. 16' total (sectional doors only).

PIVIN-BCSI

Special Order BCSI Gate Operator ** Price by Quote Only

MGJ-5011U-RH

LiftMaster Medium-Duty Logic Gear-Reduced Op. 1/2 HP 115V 1Ph Right Hand

MGJ is designed for use on rolling grilles and shutters.
Maximum recommended duty cycle: 12 cycles per hour.
Heavy-duty wormgear-in-oil-bath speed reducer
3-button station for open/close/stop functionality
315 MHz radio receiver is integral to the Medium-Duty Logic board
UL325-2010 Monitored Entrapment Capability (provides primary monitored entrapment protection through monitored photo sensors: either CPS-U or CPS-UN4 or a 4-wire monitored edge using the CPS-EI interface)

.......more details

Installation manual Sell sheet

TRACK-3"-RAW-14

Raw Vertical Track 3" 14'-0" Sold per Piece

070032-0000

Overhead Double Drive Pulley

MG00014

Micanan Slotted Hex Nut 3/4"-24UNF

PRO-H/HB operator parts

27-24417

Truck Door Dual Torsion Spring Assembly 96/35 for Whiting Roll-Up Doors

Assembly includes: shaft LH & RH springs winding cones cable drums with bearings and spring spacers.
Springs are treated with rust preventative
Roadside cable drum is color coded RED
Specs: Shaft Length: 96" Spring Length: 35" Wire diameter: .187 Winding cone color: White

36196A

Genie Sprocket Saddle

Sprocket Saddle for Genie PMX Chain Drive Openers With T Rail
Uses # 27191A.S Sprocket ( Not Included)

PRO-GH-10083U-L

Micanan 1 HP 208V 3P Gearhead Op. N1 Eyes Monitored ECB Left Hand

Designed for use on all rolling doors and grilles and for large sectional doors with high or vertical lift.
Full function smart 10.0 logic board featuring on-board receiver with antenna and enhanced program selections.
External radio control terminal strip
Three button O/C/S control station Nema-1
Supplied with Nema-1 photocells
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

MP00055

Micanan Track and #410 (#48) Chain for 10' h Door *Actual length 150"*

For 1/3 & 1/2 HP Micanan trolley operators

MP00088

Micanan Track and #41 Chain for 8' h Door *Actual length 126"*

For 3/4 & 1 HP Micanan trolley operators

GM-809

Gear Master

Holds shaft assembly for easy removal of roll pins
Makes changing gears easy

SL14COP-50

Copper Sleeve 1/4" 50 Sleeves per Pkg *price on request

Oval sleeves ONLY
Stops sold separately part # ST14COP

MK-00430

Micanan Capacitor 240V/250V 70 Mf

For limited duty 110V operators

.262-334-L

Cut-to-Length Torsion Spring .262 x 3-3/4" Left Hand Wound Red/Yellow

Priced per inch
For factory installed cones priced seperately - use part no. C-375-INSTALLED

PRO-H-5053U-LH

Micanan 1/2HP 575V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

Installation manual Specification sheet

12131

Doorlec Brake Disc 4" x 5/8" Keyway

Fits Doorlec model SGOH

19054

Doorlec VBelt 5L380

works on model SWGO

E3JM-30FT

Omron Thru-Beam Photoelectric Sensor Nema 4 0-30ft Range

Easy-to-wire terminal block
Built-in timer offers selectable ON-delay OFF-delay and one-shot
Relay or transistor output models
Light-ON/Dark-ON operation switch selectable
Model: E3JM-10M4-US

60-7241

Standard Caution Sign French 12" x 24"

34030308

Polyester Lifting Sling Type 3 Eye / Eye 3" x 8'

2-ply
Minimum tensile strength of 9800 lbs per inch of width

38079001

Agri Safety Chain GR 70 3/8" x 69"

Min. strength: 20200 lbs
Includes hook joiner link & tag

.331-514-R

Cut-to-Length Torsion Spring .331 x 5-1/4" Right Hand Wound Red/White

Priced per inch - cones and filler sold seperately
For factory installed cones use part no. C-514-INSTALLED
For spring filler use part no. SPRING-FILLER

K94-37236

LiftMaster Universal Solar Harness Kit

For 7 Ah and 33 Ah batteries

BL-16

Barlock Kit Complete for 16ft Wide Door Kit includes hardware bag

Kit includes hardware bag and bars (97-1/2")

Assembly Manual

770

Fasteners Hex Serrated Flange Head Bolt 3/8-16 x 1" 1000/Box

Zinc
Grade 5

K72-13057

LiftMaster Clutch Shaft Kit APT

Kit contains: Clutch Plate Clutch Shaft Bearing 3/4" I.D Sprocket 41B10x3/4" 5L Belt Motor Pulley Spring Clutch Disc Shim Washers Castle Nut Flatwashers Cotter Pin Roll Pins and Push on Fastener.

07-8058

LiftMaster Crank Link BG790

PRO-HBH10011U-R

Micanan 1 HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand (Pro-HHD)

1 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn o/s/c (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

HTR-460

LiftMaster Heater Kit for AC Pad Mount Gate Operators 460V Only

Heater kit for pad mount 460V AC gate operators.
Includes transformer
Battery bracket NOT included.
Protects system to -40° F and installs on operator frame

1104-18FT-BRONZ

Residential Side & Top PVC Weather-Strip with cap 18' Long - Bronze (F)

Bronze rigid vinyl retainer with bronze flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.
Full case quantity only (12).

801-300-001-00

Equinoxe Long Range Receiver 1-Door 433 MHz Pre-2016 *** To Extent of Inventory

1000 ft range
Old generation - prior to 2016

Programming Instructions Instructions de programmation

2B639

LiftMaster Speaker for EL25 (41B0639)

1B0639

15-50B12LGH

Sprocket 12 Teeth 1" Bore 1/4" Keyway

Same as 50B12x1

TS-15

Tarp Strap Bungee with Galv. S-Hooks 15"

Made of 100% natural rubber from Sri Lanka
Galvanived S-hooks
15" safely stretches to 23"

5735.96

Whiting Bottom Seal Grey 96"

For Dry Freight and Truss Doors

MCT-1

Linear 1-btn MegaCode Visor Transmitter 318 MHz

Activates one 318MHz MegaCode receiver
Test/operate LED
Visor mounting clip supplied
Power: 9-volt battery incl.
Codes: 1000000+ (MegaCode format)
Dimensions: 2.16" W x 3.75" H x .95" D

.......more details

SPRING027

Manaras Spring for Floor Level Disconnect Lever

spring for DISCONNECT001

19-5116-NP

LiftMaster Trolley Roller Chain Pack #41 for 16ft Door Nickel Plated

For 3/4 & 1 HP trolley operators

19-5112-NP

LiftMaster Trolley Roller Chain Pack #41 for 12ft Door Nickel Plated

For 3/4 & 1 HP trolley operators

17-2701

LiftMaster Pulley 7" x 5/8" (G172701)

Same as G172701

MGS20-B-2L-05

Miller Edge Sensing Edge Square Black 2-Wire Left Hand Outlet 5ft Long

��Electromechanical edge for standard 2" round or square frame sliding sing and bi-part gates. •3-sided activation allows for immediate stopping or reversing of motion •Contours to round or square posts. •Temperature range: -30F to 155F •Lead wire: 18 gauge 2ft length •Sensitivity: nominal 6-8 PSI •2 wrie NO configuration •ANSI/UL325 recognized component •Cannot be bent •One year warranty

053156

Magnetic Mount Micro Dome Beacon Amber ** To Extent of Inventory

60 LEDs 360 degree revolving flash / intermittent flash
-30 degree celsius to + 50 degree celsius extreme temperature reliability

MK-00511

Micanan Resistor 330 OHM 5Wc/w Leads (For Motor)

ZT36640159

Rolling Steel Door Model 702 Firestar No 2 Slat 22-Ga

RA-AD-WKP-05

Lynx 5-btn Wireless Keypad AD455 372 MHz

Programming Instructions Compatibility chart

R5205

Saddle Support for 4" Pulley

8 gauge galvanized steel

1104-9'-DK-SAND

Residential Side & Top PVC Weather-Strip with cap 9' Long - Dark Sandstone (DDG)

Garaga dark sandstone rigid vinyl retainer with Garaga dark sandstone flexible vinyl seal.
Dual fin vinyl.
Comes with cap to hide screws.

PBS3-GREEN

Replacement Button Only - Green

Replacement button for 02-403P

H105L5-LH

LiftMaster Ind. Duty Hoist Op. 1 HP 575 VAC 3 Ph Logic 5 Left Hand W/Brake

Includes CPS-U
H-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
The operators are typically mounted to the wall when used with larger sectional overhead doors with vertical or high lift and mounted to the wall or the front of the hood when used with rolling doors and grilles.
H operators are attached to the door jackshaft to indirectly drive the door. Connectivity
MyQ® Technology enables you to securely monitor and control your facility operator and lights with your smartphone tablet or computer for greater peace of mind.
Alerts can be received as email or pop-up (push) notifications on a mobile device ensuring the status of your commercial door.

.......more details

Installation Manual Manuel d'installation Sell sheet Brochure

MOUNTSHAFT010

Manaras Hoist Shaft Kit for MJH (pre-1998)

Drawing

EQ2722

SkyLink 3/4 HP Garage Door Opener with 2 2-Btn Keychain Remotes ** Discontinued

The DC motor offers additional benefits with very quiet operation and much less vibration.
It is ideal for garage doors that are below a living room or bedroom.
The DC motor also offers the soft start soft stop features which reduces the vibration and wear and tear of all the mechanical parts
Features: Rolling Code Technology Soft Start Soft Stop Optimal Force Learnings and Safety Beam Sensors.
Available in either Belt or Chain drive
Includes two 2-btn keychain remotes # MK318-2

.......more details