The RapidoTM RVH is a high-speed heavy-duty V-belt drive industrial operator designed for use on vinyl rolling doors as well as rolling bug screens.
RVH offers an opening speed up to 30”/sec while smoothly managing Soft-Starts and Soft-Stops therefore reducing the wear and tear of the complete door system.
#41 or #50 roller chain with sprockets selected for an optomized door opening time.
Electrically activated drum-band type solenoid brake.
All electrical components are in a Nema 1 enclosure. Hinged electrical enclosure cover
6-digit electro-mechanical counter mounted inside the control box counts each complete door cycle providing valuable data for maintenance scheduling.
The EXA-1000 is a 1/2 wave center fed vertical antenna composed of three parts: an Antenna assembly with an F connector attachment; a Base Plate assembly with radial mounting provisions; and a five-foot 75-ohm coaxial cable.
The cable connects to the antenna base on one end and the receivers F connector on the other.
If the antenna must be mounted further than five feet from the receiver an extension cable of up to a maximum of 25 feet may be used instead of the five foot cable supplied.
Because of the cable resistance the performance of the EXA-1000 may be degraded by using longer than a 25 foot cable
Compatible with all Linear receivers with Type F antenna connector
The Silencio operators have integrated noise reducing enhancements which make it 4X QUIETER than the Premium Trolley Apartment model (OTBH-A.05).
A low headroom apartment type garage door operator designed for use on industrial standard lift sectional doors with high cycling daily frequency requirements
Mounting (Low Headroom Design): Ceiling-mounted with only 6.25" headroom clearance required below the tracks. For indoor use only.
Dimensions: Back Room: door height + 4'5" (1350 mm)
Head Room For Tracks: 5.625" (143 mm) above the highest point of door travel
Comes with carwash modification and tracks/chain for doors up to 12ft
The direct drive operator consists of a DC electric motor directly coupled to a hollow shaft (30:1 reduction) worm gear reducer designed to install over keyed door shaft.
Continuous duty 0.5 HP 90 V DC 1750 rpm motor suitable for
110 to 240 V 1 PH and 60 Hz power supply.
Comes with integral absolute encoder to control the door travel
24 V 5 amps back-up battery pack and 3/8” ratchet socket to
accept and crank for manually operating the door in case of power failure
Programmable wall mountable UL325 compliant NEMA 4X control panel with LCD display and OPEN-CLOSE-STOP buttons on cover
Easy wall or post mount vehicle tag/prox card reader can service an entire facility parking garage gated community/HOA or guarded properties.
Integrates into (CAPXL CAP2D) Liftmaster PPWR Passport Receiver and LiftMaster CSW24U 24 VDC Commercial Swing Gate Operator CSL24UL HCTDCUL systems to give access via encrypted-digital code.
Opens swing or slides gates from 20-30 feet distance
26-bit Wiegand Interface console
Encrypted binary protocol signal
Helpful Programming/Testing/Function tri-color LEDs on both reader face and Wiegand console
The keypad is housed in a rugged plastic enclosure and is designed to be mounted in a standard single-gang electrical box. The die-cast keys have bright easy-to-read yellow graphics.
It is supplied with four different plastic snap-on mounting bezels to customize the look of the keypad. The satin-chrome bezel comes factory installed on the keypad. The white ivory & bronze bezels are packaged separately.
Up to 480 entry codes from 1 to 6 digits in length can be programmed. They can activate either or both of the relay outputs.
Relay #1 has a 5 Amp capacity. Relay #2 has a 1 Amp capacity. The relays can be set for timed or latch-on/latch-off toggle operation per each individual entry code.
The on or off toggle state of a relay is maintained even after power interruption. When power is restored to the keypad each relay will assume the state it was in when power was removed.
Manufactured to the highest quality standards to ensure accurate detection our Pre-formed loops come with a 50 foot twisted lead-in ware and available lead-in lengths up to 500 feet.
Ideal for use on existing asphalt or concrete surfaces
Features a non spliced continuous wire throughout loop turns and lead-in.
requires the use of loop sealer when being installed to ensure long lasting trouble-free detection