Devanco Canada - Get The Right Garage Door Opener‎ and Parts

10W8

Resistor 10W 8K OHM

ETH-A

Doorlec Trolley Type Apartment Op. 1/2 HP 120V Head Only

This operator can be wire to receive radio and photo electric control systems loop detectors etc..
Headroom Required: 2" minimum at doors highest arc of travel

SBB-3

3" Safety Bottom Bracket Low Tension Sold as a Pair Torque Force

Includes 1-Right hand and 1-Left hand
Zinc plated Steel
Max Door Weight: 2200 LBS
Cable attachment: Fixed
Protective cover: No
Use with: Straight track 3"

.......more details

Installation instructions Instructions d'installation Spec sheet

MIRCU-02

Miller Edge Universal Non-Monitored Interface

Converts a monitored pulsed signal to a non-monitored normally open signal
Creates a Fail Safe signal; reports a fault when power is lost
Ideal for use with pre-2010 commercial door operators

Installation instructions Sell sheet

3EBX

Explosion Proof 3-Btn Pushbutton Control Station

Not rated for division or class
Three button O/C/S Nema-7/9
Surface mount
Dimensions: H=6-1/8" x W=3" x D=4-3/8"

112561

Allstar MVP-RE 24V 8 Wire Receiver 288 MHz *** No Longer Available

Three channels – three relay outputs
8-wire operator connection
Wire whip antenna with “F” connector
Compatible with Allstar Classic Allister and Pulsar dipswitch transmitters and MVP quik-code transmitters
Power: 24 VAC/VDC
Codes: 19683

.......more details

ACP00942

Linear Control Board for Telephone Entry System AE-100

Board only for AE-100 telephone entry system

36045A

Genie Helical Gear 2040L

Helical gear assembly for the Genie #2040L garage door opener.
Same as: 36045AS 36045. 36045A 36045S
Includes: Helical and limit gear screws clips and small tube of grease.

SELECTOR-BTN-8L5

Devanco replacement rotating black button for 8L5-OCS

replacement black button but for rotating 8 position selector for 8L5-OCS

SELECTOR-8L5

Devanco replacement rotating 8 position switch selector for 8L5-OCS

replacement rotating encoded 8 position selector for 8L5-OCS

JA383

FAAC Sprint 383 Board 115V

RP-BRK-WALL

Lynx Wall Bracket RSI

MICANAN-H/CHAIN

Micanan Charge for Hand Chain on Doors Over 16'

Up-charge only

MLC-K72

Miller Edge Light Curtain Monitored 6ft Pulsed

Light curtain made up of a series of thru-beam photo eyes designed to provide a dense barrier of protection for motorized or high speed doors.
Ideal for environments that require expanded protection for protruding parts that may not be detected by standard single-beam photo eyes mounted 6" above the floor.
Ability to span up to 32' wide
Universal mounting brackets included
IP67 waterproof housing not recommended for carwash applications
Operating temperature: -40F to 140F

.......more details

Installation manual Sell sheet

SL595101UL

LiftMaster Dual Voltage Slide Gate Op.1 HP 115/208/230V 1 Phase - Heater NOT Incl. Reflective photocell LMRRUL included****NLA

Power: 115/208/230 VAC. Single Phase.
Accessory power: 24VAC 500mA max.
Monitored safety inputs: 3 Main Board 3 Expansion Board.
Temperature specs: Without Heater: -4°F (-20°C) to 140°F (60°C). With optional heater (HTRNB: HTR460 for 460V operators): -40°F (-40°C) to 140°F (60°C)
Gate travel speed: 12 in. per second.
Security+2.0® on-board radio receiver: Up to 50 remote controls (unlimited with 811LM/813LM).

.......more details

Installation manual Manuel d'installation First step for installation Première étape pour l'installation Sell sheet Wiring diagram Wiring diagram 575V

VPL-12

Autogate 12V Motor

HSLG-121

Linear Commercial Slide Gate Operator 1 HP 230V 1 Ph - Heater not Included

Max duty cycle: Continuous
Integral APeX Controller
Double V-belt to chain reduction
#40 roller chain
Emergency manual disconnect handle
Powder coat finish

.......more details

BG790-5021

LiftMaster Ind-Duty Wishbone Barrier Gate Op 1/2 HP 230V 1Ph - Comes w/Arm & Counterweight

A reliable gear-driven barrier gate operator that is perfect for industrial applications.
This barrier gate is designed for Wishbone-Type Arms with lengths of up to 24 ft.
The BG 790's powdercoated weather-resistant steel enclosure and its 1/2 HP commercial motor ensure strong dependable performance.
Standard Features: Control inputs and Adjustable limit settings
02-102 Open/Close Push Button Included

SGP-321-1-230/1

Doorlec Gate Master 1 HP 230V 1 Phase with Heater and Lights in Cabinet

Post mount heavy-duty industrial slide gate operator
Max. gate weight: 2500 lbs
Gate travelling speed: 45 ft / minute
175 watt heater included

Technical Information Sheet Fiche Technique Electrical Diagram Diagrammes Electriques

CGH751L5-RH

LiftMaster Gearhead w/ Brake & Carwash Mod. 3/4HP 115/230V 1P L5 - Right Hand

Gearhead style commercial door operators employ lubricated gears for heavy industrial high cycle applications.
GH-style operators include a floor level chain hoist to ease manual operation in an emergency or power outage.
Hoist wheel is easily moved to Right or Left hand side of unit eliminating the need to order right or left hand mounting.
MyQ Technology enables you to securely monitor and control your facility operator with your smartphone tablet or computer. Internet Gateway 828LM required.
Security +2.0 radio receiver safeguards your facility - with every click a new code is sent to the commercial door operator so the door opens only for you.
Timer-To-Close: Conveniently and confidently closes the commercial door automatically after a predetermined amount of time has elapsed for added security and peace of mind.

.......more details

Damp Environment Modification

Q025

LiftMaster Motor Pulley 2-1/2" OD 1/2" Bore (K17-50098)

Replacement motor pulley of motor output shaft for Liftmaster Elite models SL3000UL and CSW2000UL

PRO-APTC-5083-U

Micanan 1/2HP 208V 3P Apartment Trolley Op. Photo Eyes Monitored ECB

Low clearance design for APT applications (8.5")
Door speed: 7" per second
N-4 Micanan compatible monitored photocells included
Monitored board
Side access hinged cover for easy access to controls
Three button open-close-stop control station Nema-1

.......more details

Installation manual

PL-A22-BOARD

Lynx RPM Reader Board Proline

3500

Whiting Beverage Align Roller 1" Screw Type

A Whiting original

210134

Skylink Pulley Assembly - Belt

Fits Skylink & Mastercraft 046-0266-0 belt model openers

26CW94623-CUT

Truck Door Top Panel Painted White (13" x Cut-to-Size) for Whiting DryFreight

These panels are cut to an extra wide width to fit wider vehicle applications
Interlocking tongue and groove design for weather-tight joint and proper alignment.
Non-routed
.75" thick 7 ply exterior grade medium density plywood
Painted white

IRB-TX

EMX Industries Transmitter Board Only for IRB-4X *** No Longer Available

COUPLER-LJ-OHD

Coupler Love-Joy for Overhead Door

ALUM-5P5

Aluminum 24" x 100' Spool Graphite # 5P5

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 5P5
Reverse side is #431 Bright White

Colour chart

.235-3.25-11.5-LHW

Mini Storage Spring .235 x 3.25" x 11.5" long Left Hand

PRO-4X_MOD_3HP

Micanan Nema 4X Modification 3HP

This modification provides a washdown motor N-4X corrosion proof stainless steel control box enclosure waterproof drive and limit chain and a corrosion proof three-button station.
For options M & U Micanan N-4X photocells are supplied
For 3HP motors

MW-00232

Micanan In-Line Torque Clutch Assembly Modification

Clutch is mounted in between motor and reducer flange
Overall length of operator increases by 3.85"
For models PRO-GH / GHC 1/2hp 3/4hp 1 hp 1.5hp & 2 hp

PRO-GH-7521U-R

Micanan 3/4HP 230V 1P Gearhead Operator N1 Eyes Monitored ECB Right Hand

Includes 3-btn O/C/S control station Nema 1
External radio control terminal strip
Heavy duty worm gear reduction in oil bath gearbox
Solenoid brake standard
#50 roller chain and sprockets on final drive
Emergency chain hoist with electrical cut-out switch for manual operation

.......more details

Installation manual Specification sheet

MOTOR189

Manaras Electric Motor 1/2HP 120V 1PH

Instant reverse
Medium-duty 1050 rpm
For OMT MLJ MLH MLT

PRO-HB-7583U-RH

Micanan 3/4HP 208V 3P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included

PRO-HB-5083U-RH

Micanan 1/2HP 208V 3P Hoist Op. with Brake N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake included
On-Board receiver holds up to 20 transmitters

LA412DCS

LiftMaster Secondary 12VDC Solar Actuator Arm for Dual Swing Gate Applications

Installation manual Manuel d'installation

229557

Torque Force EZ Low Headroom Conversion Kit

Reduced headroom as low as 8"
Convert a standard lift door to a low headroom door without using an outside hookup configuration.
Easy to install 3 piece kit
Fits on 15" radius and 12" tracks

PRO-H-7543-U-LH

Micanan 3/4HP 460V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL

PRO-H-5038-U-LH

Micanan 1/2HP 380V 3P Hoist Operator N1 Eyes Monitored ECB Left Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

PRO-H-5021-U-RH

Micanan 1/2HP 230V 1P Hoist Operator N1 Eyes Monitored ECB Right Hand

Continuous duty belt drive jackshaft operator with emergency chain hoist
Full function Smart 10.0 Logic control board featuring on-board receiver with antenna
Nema 1 photoeyes included
Solenoid brake OPTIONAL
On-Board receiver holds up to 20 transmitters

DW-RS-200

Fraba Wireless Air Wave Switch Transmitter/Receiver Kit NOC/NCC

The small radio transmitter unit and the pneumatic switch are packaged within the DW3S-200 case while the receiver is built into a Nema 4 case
It is equipped with a NC or a NO relay
Kit includes radio transmitter DWTR-200 433 Mhz and receiver RSW-R 433 Mhz
Battery is included # CR2032

Operating Instructions

K71-D1PH

LiftMaster Drum Brake Kit 1 Ph 115/230V (Late Model Logic 5 Shoe and Drum Models)

Internal Solenoid Drum Brake with Cable (120V Single Phase) Replacement Kit.
Compatible with LiftMaster® Logic 5.0 Model T SD J H and HJ Industrial-Duty Operators.
Complete service kit includes: Solenoid Cover Brake Solenoid Brake Drum Cable Mounting Plate and Installation Hardware.
Quiet preferred sound profile
Industry benchmark stopping performance with adjustability
Significantly reduced modes of failure

.......more details

Installation manual Manuel d'installation

PRO-J-10023-U-LH

Micanan 1HP 230V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

MK-00049

Micanan Overload Reset 3-Phase 1.8 - 2.6 Amps

MK-00052

Micanan Overload Reset 3-Phase 5.5 - 8.0 Amps

MK-00175

Micanan Transformer 200V-110V-100VA

MK-00223

Micanan Transformer 460V-110V-100VA

MK-00141

Micanan Transformer 220V-24V-100VA

MK-00222

Micanan Transformer 460V-24V-100VA

MP-00077

Micanan Heavy Duty Front Idler (Trolley End Bracket) #41 w/Pillow Blocks

MK-00099

Micanan Utility Limit Switch w/Roller (Telemecanique # XCKL115H7)

Installation Manual

MV-00029

Micanan 110V Commercial Receiver NEMA-4 CR32E-110V

MK-00059

Micanan Timer 7 Day/24hr Economical

MP-00081

Micanan Double V-Belt Mod. for PRO-J H HHD

Provides added strength to the belt drive system

MV-00239

Micanan Key Switch O/C/S Btn Tamper Proof w/Best Core Cylinder Nema 1 Flush Mount

MK-00785

Micanan 3-btn O/C/S Nema-7/9 Pushbutton Control Station

Surface mount
Killark

MV-00003

Micanan 3-btn O/C/S Nema-1 Pushbutton Control Station

Surface mount

MV-00004

Micanan 2-btn O/C Nema-1 Pushbutton Control Station

Flush mount

MK-00522

Micanan Relay 24 VAC 8-Pin Plug-In

SD105L5-RH

LiftMaster Heavy-Duty Slide Door Operator 1 HP 575V 3PH Right Hand (Must include hardware box)

Perfect for split and sliding doors involved with industrial applications.
It is installed above the door and corresponds with the direction the door will be traveling.
Comes equipped with an emergency disconnect and for manual lifting in an emergency and automatic reconnect.
The new logic 5 commercial operators come with MyQ Technology built in. * 828LM required
Built In Security+ 2.0 radio receiver
Solenoid brake included

.......more details

HAML-SHAFT-ADAPTR

GDI Shaft Adaptor 1" w/Sprocket Vertical Mount Application

.421-6-L

Cut-to-Length Torsion Spring .421 x 6" Left Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

.295-6-R

Cut-to-Length Torsion Spring .295 x 6" Right Hand Wound Blue

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

.283-6-L

Cut-to-Length Torsion Spring .283 x 6" Left Hand Wound White

Priced per inch
For factory installed cones priced seperately - use part no. C-600-INSTALLED

LMWETXU

LiftMaster Wireless Edge Transmitter Monitored

Connects to wireless edge receiver using low-energy Bluetooth transmission
Sensing distance up to 130 ft
Transmitter accepts up to 2 wired resistive edges
Battery life 2 years
NEMA 4X rated
Compatible with LMWEKITU Wireless Edge Kit and L50 and S50 Monitored Resistive Edges

.......more details

Installation manual Manuel d'installation Product Guide Guide de produit

PRO-LJ-5021-U-LH

Micanan 1/2HP 230V 1P Jackshaft N1 Eyes Monitored ECB Left Hand

On-Board receiver holds up to 20 transmitters

PRO-GT-10043-U

Micanan 1HP 460V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

PRO-GT-7581-U

Micanan 3/4HP 208V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

SPRAY-265

Aluminum Touch Up Spray Paint Antique Brown / Brun Antique #265/165 *** To Extent of Inventory

140g

ALUM-507

Aluminum 24" x 100' Spool Tan / Tan # 507

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 507
Reverse side is #431 Bright White

Colour chart

K001A6426-2

LiftMaster Control Board RSL12V/RSW12V

60-7248-888XL

Wheel Chock Safety Pkg incl'd: laminated chock wall bracket 15' chain 3/8" x 1 7/8" anchors (4) & 3/16" quick links (2)

System Includes (1) 88-8XL Chock Bracket Tie Back Chain English and French Caution Signs and (4) Wall Bracket Anchors
Made From Used Truck Tire Laminates Compressed and Fastened Under High Pressure
Galvanized Steel Sides
Size: 11-1/4" wide x 14" long x 14" high

42GRR-9001

Allen Bradley Series 9000 Photoelectric Sensor Thru-Beam Receiver Unit

nput: 20-40VAC 10-55VDC 4VA

K10-33850

LiftMaster E-Box Cover MH MJ MT

STRUT-2-1/4-10'

Door Strut 2-1/4" Hemmed 10 ft Long

Reinforcement bar 2-1/4"
Electro-Galvanized
22-GA

HCRH1

Hinge Combination Roller Hinge Assembly #1 Galvanized

MP-00204

Micanan Splash Proof Covers PRO-H J HHD GH GHC (Fully Assembled)

drawing

CAPXL

LiftMaster Connected Access Portal High Capacity

Connected Access Portal High Capacity Cloud-based access control for residential communities.
Capacities: 4 Controlled Gates/Doors
Wireless Link for up to 8 LiftMaster® Operators
4 to 8 Digit Entry Codes
4 to 6 Digit Directory Codes
50000 Local Resident Capacity

.......more details

MM00021

Micanan Disconnect Lever MSI0012

D4-120

Extruded Bumper Black 120" L x 4 1/2" W x 3 3/4" H w/Metal Insert

Sold in 10' Lengths and cut to measure
Includes 10' Metal Washer Insert
Comes with 5 Holes for mounting or none - Please Specify When Ordering Bumper

LB1210-24

Laminated Bumper Standard Black 10" x 24" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB610-18SF

Steel Faced Laminated Bumper Black 10" x 18" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

RESET014

Manaras Resettable Overload Fuse 17A 1 Phase

41A4371

LiftMaster Belt Cap Retainer

Same as 41C4371

26CW14225-CUT

Truck Door Bottom Panel with Hardware (15" x Cut-To-Size) Painted White for Todco Dryfreight

These panels are cut to an extra wide width to fit wider vehicle applications.
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels are routed and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes with 18" pull strap assembly two bottom fixtures standard lift handle two cable anchor brackets seal and retainer.

.......more details

8500W

LiftMaster Res. Jackshaft BBU Garage Door Opener Wi-Fi ***No Longer Available

Built-in Wi-Fi for the easiest way to connect the garage.
MyQ mobile app lets users receive alerts and control the opener from anywhere.
MyQ Remote LED light can be placed anywhere to provide bright maintenance-free illumination.
Wall-mount design and quiet DC motor eliminate noise and vibrations through the ceiling and provides smooth operation.
Heavy-lifting power operates doors up to 850 lbs.
Integrated battery backup ensures access even when the power’s out and will open and close the door twice a day for 5 days

.......more details

Installation manual Manuel d'installation Sell sheet Brochure Product guide

RP-TRF-110-2415VA

Lynx Transformer 110/24 15VA *** No Longer Available

For old 455 Automatic Doorman opener

RADIO-EM932

Manaras 32-Door Dip Switch Transmitter O/C/S

3-button transmitter
Operates up to 32 doors by using a combination of 2 rotary dials and dip switch keys
Open/Close/Stop function
LED Indicator
Soft touch push buttons including a bright red stop button for easy identification
Includes 4 mounting screws and anchors

.......more details

Programming instructions Manual

MV-00296

Micanan Wireless Push Button Station OCS for Logic 10.0

Used only on Logic 10.0 program 3.2.5

2376.171_25.930

Whiting Torsion assembly .171 wire size 25" spring length 93" shaft

IRB-RET-HD

EMX Industries Steel Protective Hoods Only Black Fits Old Style IRB-RET Only *** No Longer Available

Protective Hoods for the Universal Retro-Reflective Monitored Photo Eye System (Item #IRB-RET) by EMX
Easily installed using the existing mounting holes of the Photo Eye
Constructed of zinc plated steel
Black powder-coated finish
Will NOT fit the new IRB-RET UL325-2018 units

LAGS141W

Fasteners Lag Screw Stainless Steel 1/4" x 1" Hex Washer Head 3/8" Sold Individually

Optional nylon washer available to create a barrier between metals see item #FW14N-W

44-60-220

Extension Spring 10' Door - 220 lbs *** By Quote Only

Clipped ends
44" long 60" stretch 220 lb load

HSLG-221

Linear Commercial Slide Gate Operator 1/2 HP 230V 1 Ph - Heater not Included

Max gate size: 35 ft 1000 lbs
Max duty cycle: Continuous
Integral APeX Controller
Double V-belt to chain reduction
#40 roller chain
Emergency manual disconnect handle

.......more details

MOD060-14FT

Manaras Auxiliary Trolley #41 Chain Modification Only

Provides drawbar operation of a standard lift door with the use of a jackshaft operator
Includes tracks for doors up to 12' high. Additional fee for over 12'
Maximum door width 22'