Devanco Canada

 
User Name:
Password:
Remember Me:
Forgot your password
Request a Login
Home
LRS-LC

EMX Logic Controller

  • For use with the Loop Replacement System (LRS-C1) Magnetoresistive Vehicle Detector Control Unit
  • Connects two stand-alone sensors to expand the detection area
  • Works with LRS-DB (LRS-DB-50 or LRS-DB-100) Direct Burial or LRS-FP Flat Pack (LRS-FP-50 or LRS-FP-100)
  • Logic Interface allows one (1) or two (2) sensors to be connected to one (1) output
  • Provides six (6) selectable logic functions and two (2) separate relay outputs
  • A/B directional logic can be selected with an output for each direction of travel as a vehicle passes over two sensors
    • .......more details
LSBLK

Loop Sealant Cartridge Black 29oz

  • Also available in grey (LSGRY)
  • Can be installed in sub-zero temperatures as long as the surface is clean and dry
  • Loop sealant gun sold separatley # LSGUN
LSGRY

Loop Sealant Cartridge Grey 29oz

  • Also available in black (LSBLK)
  • Can be installed in sub-zero temperatures as long as the surface is clean and dry
  • Loop sealant gun sold separatley # LSGUN
LSGUN

Loop Sealant Gun for Quart Sized (32oz) Tubes

  • Caulking gun for LSBLK / LSGRY
LT100HLTB3815

Telco Thru Beam Transmitter with LED M12 Hi-Power 15M Cable

  • Sensor Light Transmitter with LED
  • M12 High Power 15M Cable
LV-24-TL-RG

Narrow Lights for Loading Docks Red / Green LED 12-24VAC/DC 24-3/8" long Sold Individually

  • LED lights offer long-lasting reliable high-visibility in all weather conditions including direct sunlight with low power consumption.
  • Robust housing resists impact and corrosion.
  • Slim discrete design ensures little risk of damage due to accidental impact.
  • Wide input voltage range of 12-24Vac/dc (control box available for alternate voltages).
  • Boards coated in water-resistant polymer for optimal protection from water and humidity.
  • 24 LEDs per guide light (12 Red 12 Green)
    • .......more details
LVB1020-11

Laminated Bumper Black 10" Projection Vertical Installation 20" x 11" Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB1024-11

Laminated Bumper Black 10" Projection Vertical Installation 24" x 11" Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB1220-11

Laminated Bumper Black 12" Projection Vertical Installation 20" L x 11" W Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB1224-11

Laminated Bumper Black 12" Projection Vertical Installation 24" L x 11" W Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB420-11

Laminated Bumper Black 4" Projection Vertical Installation 20" x 11" Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB420-11/P1

Laminated Bumper Black 4" Projection Vertical Installation 20" x 11" Sold Individually Style P1

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
Specification Sheet
LVB420-11SF

Steel-Faced Laminated Bumper Black 4" Projection Vertical Installation 20" x 11" Sold Individually

  • Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
  • Can be used in material handling application where medium to heavy dock protection is required.
  • 5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
  • Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
  • Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
  • Brackets to be punched with elongated holes to allow steel face to "float" upon impact.
    • .......more details
LVB420-11SF/P1

Steel-Faced Laminated Bumper Black 4" Projection Vertical Installation 20" x 11" Sold Individually Style P1

  • Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
  • Can be used in material handling application where medium to heavy dock protection is required.
  • 5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
  • Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
  • Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
  • Brackets to be punched with elongated holes to allow steel face to "float" upon impact.
    • .......more details
LVB420-11SF/P2

Steel-Faced Laminated Bumper Black 4" Projection Vertical Installation 20" x 11" Sold Individually Style P2

  • Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
  • Can be used in material handling application where medium to heavy dock protection is required.
  • 5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
  • Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
  • Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
  • Brackets to be punched with elongated holes to allow steel face to "float" upon impact.
    • .......more details
LVB424-11

Laminated Bumper Black 4" Projection Vertical Installation 24" x 11" Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB424-11SF

Steel-Faced Laminated Bumper Black 4" Projection Vertical Installation 24" x 11" Sold Individually

  • Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
  • Can be used in material handling application where medium to heavy dock protection is required.
  • 5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
  • Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
  • Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
  • Brackets to be punched with elongated holes to allow steel face to "float" upon impact.
    • .......more details
LVB430-11

Laminated Bumper Black 4" Projection Vertical Installation 30" x 11" Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB436-11

Laminated Bumper Black 4" Projection Vertical Installation 36" x 11" Sold Individually

  • For use in low to medium traffic loading docks in factories and warehouses.
  • Can be used as rub rails at the sides of truck wells
  • Fabric reinforced rubber pads cut from recycled truck tires.
  • Rubber pads laminated between steel angles and secured with 3/4” rods
  • Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
  • Wall mounting hole size is 1” diameter.
    • .......more details
LVB436-11SF

Steel-Faced Laminated Bumper Black 4" Projection Vertical Installation 36" x 11" Sold Individually

  • Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
  • Can be used in material handling application where medium to heavy dock protection is required.
  • 5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
  • Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
  • Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
  • Brackets to be punched with elongated holes to allow steel face to "float" upon impact.
    • .......more details