Devanco Canada - Get The Right Garage Door Opener‎ and Parts

MG-00127

Micanan Plastic Spacer for Boards (Short Length 0.382)

MK-00645

Micanan Plug-In Harness for External Radio Control 3-Wire

MK-00666

Micanan RF Junction Connector for Antenna

MK-00041

Micanan Overload Reset 1-Phase 12 Amps

MK-00523

Micanan Reversing Contactor ABB Size 1 24V w/Interlock

LC2K1210B7 mini contactor

MV-00220

Micanan Pull Cord DPST Swivel Type - Nema 4

MV-00018

Micanan Key Switch ON/OFF Nema 4 Surface Mount

MV-00010

Micanan 3-btn O/C/S Nema-4 Pushbutton Control Station

Surface mount
Metal Housing

MV-00172

Micanan LCE-3 Nema-1 Pushbutton Control Station

Flush mount

MV-00006

Micanan 3-btn O/C/S w/Key Lock-Out Nema-1 Pushbutton Control Station

Flush mount

MK-00031

Micanan Transformer 230V-24V-40VA

PRO-J-10021-U-LH

Micanan 1HP 230V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

.421-6-R

Cut-to-Length Torsion Spring .421 x 6" Right Hand Wound Gold

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-600-INSTALLED

.437-514-L

Cut-to-Length Torsion Spring .437 x 5-1/4" Left Hand Wound Red/Green

Priced per inch - cones sold seperately
For factory installed cones use part no. C-514-INSTALLED

.406-514-R

Cut-to-Length Torsion Spring .406 x 5-1/4" Right Hand Wound Blue/Yellow

Priced per inch - cones & filler sold seperately
For factory installed cones use part no. C-514-INSTALLED

.343-258-R

Cut-to-Length Torsion Spring .343 x 2-5/8" Right Hand Wound Blue/Red

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.312-258-L

Cut-to-Length Torsion Spring .312 x 2-5/8" Left Hand Wound Yellow

Priced per inch - cones sold seperately
For factory installed cones use part no. C-258-INSTALLED

.283-514-R

Cut-to-Length Torsion Spring .283 x 5-1/4" Right Hand Wound White

Priced per inch
For factory installed cones priced seperately - use part no. C-514-INSTALLED

ME117-2W-BLK-U

Miller Edge 2-Wire Black Universal Outlet Sold by the Foot

Electromechanical slide in edge for 1" to 2" sectional doors.
Touch sensitive signaling allows for immediate stopping or reversing of motion. The ME117 is resistant to water flame and most common greases and oils.
Temperature range: -30F to 155F
Lead wire: 22 gauge universal
Sensitivity: nominal 6-8 PSI
2 wire NO configuration

.......more details

Installation manual Sell sheet

PRO-J-7511-U-LH

Micanan 3/4HP 115V 1P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-J-5043-U-LH

Micanan 1/2HP 460V 3P Jackshaft Monitored ECB N1 Eyes Left Hand

On board receiver with antenna
Continuous duty industrial motor with overload protection
Heavy duty 5L V-belt
Adjustable friction clutch
Solenoid brake (optional PRO-JB) recommended for large doors
3/4" permanently lubricated & sealed precision ball bearings on pulley shaft

.......more details

Specification Sheet

PRO-GT-15023-U

Micanan 1-1/2HP 230V 3P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-GT-15021-U

Micanan 1-1/2HP 230V 1P Worm Gear Trolley Operator N1 Eyes Monitored ECB

On-Board receiver holds up to 20 transmitters

PRO-APT-7523-U

Micanan 3/4HP 230V 3P Apartment Trolley Operator N1 Eyes Monitored ECB (PRO APTE)

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board

PRO-APT-7511-U

Micanan 3/4HP 115V 1P Apartment Trolley Operator N1 Eyes Monitored ECB (PRO APTE)

Low clearance design for APT applications (9.5")
Door speed: 12" per second
Monitored board

PRO-TB-10043-U

Micanan 1 HP 460V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-10023-U

Micanan 1 HP 230V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-10081-U

Micanan 1 HP 208V 1P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 & 1 HP models
Monitored board
On-Board receiver holds up to 20 transmitters

PRO-TB-5053-U

Micanan 1/2HP 575V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board

PRO-TB-5043-U

Micanan 1/2HP 460V 3P Trolley Operator with Brake N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#410 roller chain on 1/2 HP models
Monitored board

PRO-T-7581-U

Micanan 3/4HP 208V 1P Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial / industrial sectional overhead doors with standard lift tracks.
#41 roller chain on 3/4 HP models
Monitored board

PRO-LT-5021-U

Micanan 1/2HP 230V 1P Commercial Trolley Operator N1 Eyes Monitored ECB

Designed for use on commercial doors with standard lift tracks that require no more than 15 cycles per hour
Trolley track for door up to 12ft standard upcharge for 14' & 16'
Door speed 9 inches per second
UL325
On-Board receiver holds up to 20 transmitters

60-7244

Econo Caution Sign French 14" x 10"

CP-SH-58-1212

Lynx Clutch Shaft Only for MCJH 5/8" x 12-1/2"

No pulley

LR110LTB3815

Telco Thru Beam Receiver M12

Remote receiver Series 110
M12 x 1 Housing Size
Nickel Plated Brass Housing Material
15 m Cable Cable Connection
IP 67 Sealing Class

MD00381

Micanan #410 Roller Chain 51 Pitch c/w Connecting Link

E/1929/031

Automatic Systems Installation Plate Ass'y BL229

Used on the BL229 gate op.

MOUNTSHAFT010A

Manaras Hoist Shaft Kit for MJH (after-1998)

For MJH MJHW/C/X built from 1999-2003

SPR50B54X11238

Sprocket 50B54 for a 1-1/2" Shaft 3/8" keyway

LB1210-14

Laminated Bumper Standard Black 10" x 14" 12" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1012-36

Laminated Bumper Standard Black 12" x 36" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB1012-14

Laminated Bumper Standard Black 12" x 14" 10" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB920-11

Laminated Bumper Black 9" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB912-14

Laminated Bumper Standard Black 12" x 14" 9" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB812-36

Laminated Bumper Standard Black 12" x 36" 8" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB820-11

Laminated Bumper Black 8" Projection Vertical Installation 20" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TVB436-11SF

Steel-Faced Laminated Bumper Black 5 1/4" Projection Vertical Installation 36" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

TB412-14SF

Steel Faced Laminated Bumper Black 12" x 14" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

TB410-18SF

Steel Faced Laminated Bumper Black 10" x 18" 5 1/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

K75-36914

LiftMaster Electrical Box Cover APT T GT SD GSD GH - L5

TB610-18SF

Steel Faced Laminated Bumper Black 10" x 18" 6 3/4" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LVB624-11SF

Steel-Faced Laminated Bumper Black 6" Projection Vertical Installation 24" x 11" Sold Individually

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required.
5/8" anchor bolts mounted through pre-drilled holes into dock or can be welded to curb angle.
Steel face is 3/8" thick heavy duty high carbon steel that is mounted over a laminated dock bumper.
Plate to be welded to 2 or 3 steel support brackets which are to extend back to the 3/4" supporting rods.
Brackets to be punched with elongated holes to allow steel face to "float" upon impact.

.......more details

LB612-36SF

Steel Faced Laminated Bumper Black 12" x 36" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LB612-14SF

Steel Faced Laminated Bumper Black 12" x 14" 6" Projection Horizontal Installation

Used on docks where excessive friction from up and down trailer movement occurs (yard jockeys air ride trailers etc.).
Can be used in material handling application where medium to heavy dock protection is required
“Gliding” heavy-duty steel face is 3/8” thick and independently anchored with elongated holes to face of bumper allowing bumper to compress AND offer high surface abrasion resistance
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.

.......more details

LLB420-22

Laminated Bumper Black 4" Projection L-Shaped 20" x 22" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 7/8” diameter.
This model has angles on both sides

.......more details

LB412-18

Laminated Bumper Standard Black 12" x 18" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB410-36

Laminated Bumper Standard Black 10" x 36" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

LB406-36

Laminated Bumper Standard Black 6" x 36" 4" Projection Horizontal Installation

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

65_52091-12

LiftMaster Manual Hoist Mod. M8 #41 Chain for 12ft High Door

For 3/4 Hp & 1 Hp Trolley operators
Includes floor level brake release cable 1" x 12' round bar.

T007

Manaras Trolley Track 7ft for 1/2HP models *Actual length 114"*

For models MLT/OTH/OTBH 1/2hp only with Chain #48 (#410)

CP-SH-34-1712_SHAFT_ONLY

Lynx Clutch Shaft Only for HDC Operators

Fits all HDC operators - waterproof or not. All HP all years
3/4" x 17 1/2" - 2.15lbs

MK-00229

Micanan Transformer 575V-24V-50VA Not Fingersafe

BTM-BK-PCG/PR

Powdercoated Commercial 3" LHR Bottom Brackets Grey Sold as a Pair (L & R) *** NLA

EZ123 UPWARDOR
Powdercoated grey
Use with: 3" straight track
Sold as a pair (includes one left and one right).

MB-03202

Micanan Electric Motor Only 1 HP 575V 3PH Base Mount O.D.P FR56

Fits T TB APT APTC J EJ H EHJ HHD SD

MM00149

Micanan GHC Frame Support U-Bracket MSI0161 (for 2 3HP)

MF00019

Micanan Hex Head Bolt 3/8"- 16 UNCx1 Full Thread

Used on PRO-GHC
6 required per operator

K74-18346

LiftMaster Limit Shaft Kit

Compatible with LiftMaster® Model GH 5HP Commercial Door Operators

MG00041

Micanan Spring Clip 7/8" ID Sold Individually

2 required per machine

BB-1

Rubber Button Cover Black for 3BLM PBS

Rubber button cover only

RCB-TIP

Roller Chain Break Replacement Tip Only *** NLA

Replacement tip only for RCB-2560

WHITING-SPEC-ORD

Whiting Special Order Parts

Special order to customer's specs

VWS-34-SANDSTONE

Screw Colored for Vinyl Weatherstrip #8 x 3/4" 1000/Box Sandstone

Pan head
S point

MP-00032

Micanan Center Mount Modification W/ No Chain Hoist PRO-J

Provides for center mount installation of a jackshaft operator
Operator output shaft is coupled in line with door shaft assembly
Couplings NOT supplied
NOTE: Reverse limit modification required

MP-00002-230V

Micanan Apartment Feature: Timer-to-Close Function and Light Control Modification only

Controlling action of two lights- sockets supplied on cover

CB380500

Cable 3/8" 7x19 500' Galvanized

Galvanized Cable 3/8" 7x19 500ft spool.
Cable break strength: 14000 lbs

MGH-6214-ECB-LH

Manaras 1 HP 240V 1P Jackshaft with Elect. Circuit Board Left Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

T118

Manaras Trolley Track 18ft for 3/4HP & ALL APT models up-charge *Actual length 246"*

For models MGT/OTH/OTBH 3/4 hp only with Chain #41

MB-02004

Micanan Electric Motor Only 3/4 HP 110/220V 1PH C-Flange TEFC 56C

C-Flange TEFC electric motor
Fits models: GT GH GHC & GSD

MB-01002

Micanan Electric Motor Only 1/2HP 110/220V 1PH Base Mount TEFC FR56

Base Mount TEFC electric motor
Fits models: TW TBW JWHWHHDW SDW

MGH-6214-CONT-LH

Manaras 1 HP 240V 1P Jackshaft Contactor Left Hand

A very heavy-duty worm gear industrial operator designed for use on Industrial standard high and vertical lift sectional or rolling doors and grilles.
It incorporates a chain hoist for manual operation with a floor level engaging device with electrical cut-out
Electrically activated drum-band type solenoid brake
Full overload protection

MB-15204

Micanan Electric Motor Only 2 HP 575V 3PH C-Flange TEFC 145TC

Fits GT GH GHC & GSD

.306-258-R

Cut-to-Length Torsion Spring .306 x 2-5/8" Right Hand Wound Red

Priced per inch
For factory installed cones priced seperately - use part no. C-258-INSTALLED

MU33-2WIRE-RH-Y

Miller Edge MU33 2-Wire NM Right Hand Yellow - Sold per Foot

MU style bumpers are designed for use with aircraft hanger doors and large specialty doors.
Must specify the exact length in feet and inches when ordering.
Mounts vertically or horizontally
Sensitivity: nominal 8-13 ibf

Worksheet

BOLT016

Manaras Hex Bolt 1/4-20 x 4

MT21-YELLOW-RH

Miller Edge 2-Wire Pressure Sensitive Edge Yellow Right Hand Outlet Sold per Foot

��Electromechanical medium profile edge for rolling fire door applications. •Touch sensitive signaling allows for immediate reversing or stopping of motion. •The MT21 is completely felixible and will contour to curved surfaces. The MT21 will also act as weatherstrip. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •2 wire NO configuration •Horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual

MP-00040

Micanan High Cycle Modification Jackshaft Models PRO-J / H only

For installations with high frequency usage
Double V-belt cast iron flanged precision bearings on all shafts and delay on reverse circuit
Supplied with #50 chain

LVB424-11

Laminated Bumper Black 4" Projection Vertical Installation 24" x 11" Sold Individually

For use in low to medium traffic loading docks in factories and warehouses.
Can be used as rub rails at the sides of truck wells
Fabric reinforced rubber pads cut from recycled truck tires.
Rubber pads laminated between steel angles and secured with 3/4” rods
Bumper is fastened to dock surface with 3/8” steel angles and/or flat plates depending on the model chosen.
Wall mounting hole size is 1” diameter.

.......more details

PROBE-150

EMX CARSENSE-101 Direct Burial Probe with 150' Lead Wire

Wand only
Requires CS101 (Carsense-101)

PRO-HBH10053U-L

Micanan 1 HP 575V 3P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Left Hand

1 HP575V 3 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

PRO-HBH-5011U-R

Micanan 1/2HP 115V 1P Heavy-Duty Jackshaft N1 Eyes Monitored ECB Right Hand

1/2 HP115V 1 PH Industrial Continuous Duty Jackshaft Operator Ideal for Sectional Doors Rolling Steel
Monitored logic board with integral 372Mhz radio receiver that can hold up to 20 transmitters (MK-00647/ MK-00653/ MK-00659) or 200 of the 1 channel hand held transmitters (MK-00660).
N-1 Through-beam (MK-00649) photocells included. Other options available.
3-btn O/S/C (02-103) wall control station included
Adjustable Friction Clutch 5L320 drive belt
#50 Roller chain 18 tooth door sprocket included

.......more details

2569.1

Whiting L-Handle Non Locking

3" shaft

26CW94222-CUT

Truck Door Bottom Panel with Hardware (12" x Cut-To-Size Painted White for Whiting Dryfreight

These panels are cut to customer's specifications
Interlocking tongue and groove design for weather-tight joint and proper panel alignment.
These panels have no routs and shipped without holes.
3/4" thick 7 ply exterior grade medium density plywood.
Painted white
Comes with pull strap two bottom roller shaft covers stud plates standard lift handle seal & retainer

.......more details

ALUM-502

Aluminum 24" x 100' Spool Maize / Ivoire # 502

20% thicker than the aluminum sold in retail stores (0.022" )
Gentek # 502
Reverse side is #431 Bright White

Colour chart

MU22-2WIRE-U-Y

Miller Edge MU22 2-Wire Universal Yellow - Sold per Foot

��Electromechanical edge for sectional doors and aircraft hangars. •The MU22 is a custom edge manufactured to exact specifications. •The MU22 is completely flexible and will contour to curved surfaces. It's profile can also be square rectangular or angled. •Touch sensitive signaling allows immediate reversal or stopping of motion. •Temperature range: -30F to 155F •Lead wire: 22 gauge universal •Sensitivity: nominal 6-8 PSI •Vertical or horizontal mount •ANSI/UL325 recognized component •One year warranty

Worksheet Installation manual Sell sheet

785149

FAAC XP15B Photocells 15m Range 785103

Surface mounted security devices with 15 m range.
The kit contains: 1 transmitter and 1 receiver.
The photocell has a BUS system technology "2easy" for easy installation.

ME120-BLK-2WIRE-R

Miller Edge Black 2-Wire NM Right Hand Outlet Sold per Foot

Electromechanical slide in edge with a small profile for motorized gates and doors rolling shutters and pinch point protection applications.
Touch sensitive signaling
Temperature range: -30F to 155F
Lead wire: 18 gauge 2ft length
Sensitivity: nominal 4 PSI
2 wire NO configuration

.......more details